5.0SMDJ12A-T7

Защитный диод - [DO-214AB, SMC]; Pрасс(пик): 5 кВт; Uраб: 12 В; Uимп(макс): 19.9 В; Iимп(макс): 252 А; Линий: 1
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Корпус DO-214AB SMC
Пиковая рассеиваемая мощность
Рабочее напряжение
Максимальное импульсное напряжение
Максимальный импульсный ток
Тип супрессора по свойствам
Количество линий ограничения
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 1

показать свернуть
Transient Voltage Suppression Diodes Surface Mount – 5000W > 5.0SMDJ series 5.0SMDJ Series RoHS Description Uni-directional Bi-directional The 5.0SMDJ series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Symbol Value Unit Peak Pulse Power Dissipation at TA=25°C by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 5000 W Power Dissipation on Infinite Heat Sink at TA=50°C PM(AV) 6.5 W IFSM 300 A • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Built-in strain relief • VBR @TJ= VBR@25°C × (1+αT (αT: Temperature Coefficient) Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25°C unless otherwise noted) Parameter Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only VF 5.0 V TJ , TSTG -55 to 150 °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25°C per Fig. 3. 2. Mounted on copper pad area of 0.31x0.31” (8.0 × 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only,duty cycle=4 per minute maximum. Functional Diagram x (TJ - 25)) • Glass passivated chip junction • 5000W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0V to BV min • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 5µA above 22V • High temperature soldering guaranteed: 260°C/40 seconds at terminals • Plastic package has underwriters laboratory flammability 94V-O • Meet MSL level1, per J-STD-020, LF maximum peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant Applications TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Additional Information Datasheet Bi-directional Cathode Anode Uni-directional © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/24/14 Resources Samples PDF
Документация на серию 5.0SMDJ 

Дата модификации: 25.01.2014

Размер: 1.03 Мб

6 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.