P6SMB170A

Защитный диод - [DO-214AA, SMB]; Pрасс(пик): 600 Вт; Uраб: 145 В; Uимп(макс): 234 В; Iимп(макс): 2.6 А; Линий: 1
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Корпус DO214AA
Пиковая рассеиваемая мощность
Рабочее напряжение
Напряжение ограничения (диапазон)
Максимальное импульсное напряжение
Ток утечки при рабочем напряжении
Максимальный импульсный ток
Тип супрессора по свойствам
Количество линий ограничения
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 2

показать свернуть
Тип Наименование Корпус Упаковка i Pрасс Pрасс(пик) Uраб Uогр(ном) Uогр(диапазон) Uимп(макс) Iраб Iимп(макс) Тип Линий Cперех Примечание Карточка
товара
P= P6SMB170A (BOURNS) 1 шт
 
P= P6SMB170A-E3/52 (VISHAY) DO214AA
 

Файлы 1

показать свернуть
Transient Voltage Suppression Diodes Surface Mount – 600W > P6SMB series P6SMB Series RoHS Description Uni-directional Bi-directional The P6SMB series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. Features Agency Approvals AGENCY AGENCY FILE NUMBER E230531 Maximum Ratings and Thermal Characteristics (TA=25°C unless otherwise noted) Parameter • Excellent clamping capability • Low incremental surge resistance • Typical IR less than 1µA above 12V • For surface mounted applications to optimize board space • Low profile package • Typical failure mode is short from over-specified voltage or current • Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c • IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) • ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) • EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) • Built-in strain relief • 600W peak pulse power capability at 10/1000μs waveform, repetition rate (duty cycles):0.01% • Fast response time: typically less than 1.0ps from 0V to BV min • VBR @TJ= VBR@25°C × (1+αT x (TJ - 25)) (αT: Temperature Coefficient) • Glass passivated chip junction • High temperature soldering guaranteed: 260°C/40 seconds at terminals • Plastic package has underwriters laboratory flammability 94V-O • Meet MSL level1, per J-STD-020, LF maximum peak of 260°C • Matte tin lead–free plated • Halogen free and RoHS compliant Symbol Value Unit Peak Pulse Power Dissipation at TA=25ºC by 10/1000µs Waveform (Fig.2)(Note 1), (Note 2) PPPM 600 W Power Dissipation on Infinite Heat Sink at TA=50°C PM(AV) 5.0 W IFSM 100 A VF 3.5V/5.0 V TJ , TSTG -55 to 150 °C Typical Thermal Resistance Junction to Lead RuJL 20 °C/W Applications Typical Thermal Resistance Junction to Ambient RuJA 100 °C/W TVS devices are ideal for the protection of I/O Interfaces, VCC bus and other vulnerable circuits used in Telecom, Computer, Industrial and Consumer electronic applications. Peak Forward Surge Current, 8.3ms Single Half Sine Wave (Note 3) Maximum Instantaneous Forward Voltage at 50A for Unidirectional Only (Note 4) Operating Junction and Storage Temperature Range Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25°C per Fig. 3. 2. Mounted on copper pad area of 0.2x0.2” (5.0 × 5.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only,duty cycle=4 per minute maximum. _ 200V and VF<5.0V for VBR > _ 201V. 4. VF<3.5V for VBR < Functional Diagram Additional Information Datasheet Bi-directional Cathode Resources Samples Anode Uni-directional © 2014 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 01/20/14 PDF
Документация на серию P6SMB 

Дата модификации: 21.01.2014

Размер: 1.05 Мб

6 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.