CS1W-CN226 CHN

Кабель (2 м.) для подключения Периферийного порта CS1/CJ1/CQM1H/CPM2C к компьютеру (RS-232C, 9 pin)
развернуть ▼ свернуть ▲

Файлы 1

показать свернуть
Ordering Information Support Software ■ Connecting Cables for CX-One Components (e.g. CX-Programmer) Name Connecting Cables between Programming Device (computer) and peripheral port Model Specifications Applicable computers IBM PC/AT or compatible computer (D-Sub 9pin) Connection configuration Cable length IBM PC/AT or compatible computer ↔ CS1W-CN226/626 ↔ Peripheral port of CPU Unit (See note.) 2m Peripheral port RS-232C Can be used CS1W-CN226 CE for both peripheral bus and host link. 6m CS1W-CN226/626 Peripheral Port Connecting Cable Computer (9-pin RS-232C) Standards Remarks CS1W-CN626 Note: If the system is a Duplex CPU System, connect to the active CPU Unit. The following configuration can be used when using an RS-232C 0.1 m cable to connect to an IBM PC/AT or compatible computer. IBM PC/AT or compatible computer ↔ XW2Z-200S-CV/V or XW2Z-500S-CV/V ↔ Peripheral port of CPU Unit (See note.) Peripheral port XW2Z-200S-CV/V or XW2Z-500S-CV/V RS-232C Cable CS1W-CN118 CS1W-CN118 Use when connecting to the peripheral port with a CXW2Z200S-CV/V or XW2Z500S-CV/V RS-232C Cable. Note: If the system is a Duplex CPU System, connect to the active CPU Unit. Connecting Cables between Programming Device (computer) and RS-232C port IBM PC/AT IBM PC/AT or compatible computer ↔ XW2Z-200S-CV/V or 2m or XW2Z-500S-CV/V ↔ RS-232C port of CPU Unit (see note 1) or compatible Serial Communications Board/Unit 5m computer (DSerial Communications Board's Sub 9-pin) RS-232C ports RS-232C Cable XW2Z-200S-CV/V (2 m) Computer XW2Z-500S-CV/V (5 m) (9-pin RS-232C) CPU Unit's built-in RS-232C port Note: 1. If the system is a Duplex CPU System, connect to the active CPU Unit. 2. We recommend the following configuration if the CXProgrammer is always connected and you want to avoid switching to the other CPU Unit when an error occurs. Active CPU Unit Terminator ON +5 V must be supplied to the NT-AL001 at computer side. 2m 5m Can be used for both peripheral bus and host link, and is equipped with an antistatic connector. XW2Z-200SCV --- XW2Z-500SCV Can be used XW2Z-200S-V for host link only. Cannot XW2Z-500S-V be used for peripheral bus. Standby CPU Unit RUN ERR/ALM DPL01 L INH BKUP PRPHL COMM SYSMAC CS1D-CPU67H R RUN DPL STATUS ACTIVE CPU STATUS ACTIVE CPU STATUS LEFT CPU USE PROGRAMMABLE CONTROLLER ERR/ALM INH BKUP PRPHL COMM SYSMAC CS1D-CPU67H PROGRAMMABLE CONTROLLER NO USE RIGHT CPU MCPWR USE BUSY MCPWR BUSY NO USE OPEN OPEN DPL SW ON OFF SPL DPL ACT. ACT. LEFT RIGHT ON PERIPHERAL +5 V PERIPHERAL INIT. SW PRPHL COMM A39512 RSV PORT ON PORT DUPLEX RS-232C CX-Programmer NT-AL001 RS-422A/485 CJ1W-CIF11 or RS-422A/485 NT-AL001 RS-422A Adapter 41 PDF
Документация на CS1W-CN226 CHN 

Дата модификации: 26.05.2016

Размер: 562.2 Кб

1 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.