STLINK-V3SET

STLINK-V3SET STLINK-V3SET debugger/programmer for STM8 and STM32 Data brief Features • Stand-alone probe with modular extensions • Self-powered through a USB connector (Micro-B) • USB 2.0 high-speed compatible interface • Direct firmware update support (DFU) • JTAG / serial wire debugging (SWD) specific features: – 3 V to 3.6 V application voltage support and 5 V tolerant inputs – Flat cables ...
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Тип
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 2

показать свернуть
STLINK-V3SET STLINK-V3SET debugger/programmer for STM8 and STM32 Data brief Features • Stand-alone probe with modular extensions • Self-powered through a USB connector (Micro-B) • USB 2.0 high-speed compatible interface • Direct firmware update support (DFU) • JTAG / serial wire debugging (SWD) specific features: – 3 V to 3.6 V application voltage support and 5 V tolerant inputs – Flat cables STDC14 to MIPI10 / STDC14 / MIPI20 (connectors with 1.27 mm pitch) – JTAG communication support – SWD and serial wire viewer (SWV) communication support • SWIM specific features (only available with adapter board MB1440): – 1.65 V to 5.5 V application voltage support – SWIM header (2.54 mm pitch) – SWIM low-speed and high-speed modes support • Virtual COM port (VCP) specific features: – 3 V to 3.6 V application voltage support on the UART interface and 5 V tolerant inputs – VCP frequency up to 15 MHz – Available on STDC14 debug connector (not available on MIPI10) • Multi-path bridge USB to SPI/UART/I2C/CAN/GPIOs specific features: – 3 V to 3.6 V application voltage support and 5 V tolerant inputs – Signals available on adapter board only (MB1440) Picture is not contractual. Description The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It is composed of a main module and a complementary adapter board. The SWIM and JTAG/SWD interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. The STLINK-V3SET also provides a Virtual COM port interface allowing the host PC to communicate with the target microcontroller through one UART, and bridge interfaces (SPI, I2C, CAN, GPIOs) allowing for instance the programming of the target through bootloader. The modular architecture of STLINK-V3SET enables to extend its main features through additional modules such as the adapter board. • Drag-and-drop Flash programming • Two color LEDs: communication, power September 2018 DB3692 Rev 1 For further information contact your local STMicroelectronics sales office. 1/4 www.st.com PDF
Документация на STLINK-V3SET 

Data brief - STLINK-V3SET - STLINK-V3SET debugger/programmer for STM8 and STM32 The STLINK-V3SET is a modular stand-alone debugging and programming probe for the STM8 and STM32 microcontrollers. It...

Дата модификации: 18.09.2019

Размер: 167.9 Кб

4 стр.

    Публикации 1

    показать свернуть
    12 августа
    новость

    STLINK-V3SET – новый программатор для микроконтроллеров STM8 и STM32

    В Компэл доступен к заказу новый автономный программатор–отладчик STLINK–V3SET, предназначенный для работы с любыми микроконтроллерами STM8 и STM32. В его комплект входят главный модуль и плата адаптера. STLINK–V3SET поддерживает... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.