STM8L101G3U6

Микроконтроллер - [VFQFPN28]
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Корпус UFQFPN28
Ядро
Максимальная частота ядра
Объём памяти программ
Тип памяти программ
Объём EEPROM памяти
Объём оперативной памяти
Количество входов/выходов
Интерфейсы
Периферия
Напряжение питания
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 2

показать свернуть
STM8L101x1 STM8L101x2 STM8L101x3 8-bit ultra-low power microcontroller with up to 8 Kbytes Flash, multifunction timers, comparators, USART, SPI, I2C Datasheet - production data Features • Main microcontroller features – Supply voltage range 1.65 V to 3.6 V – Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz) – STM8 Core with up to 16 CISC MIPS throughput – Temp. range: -40 to 85 °C and 125 °C • Memories – Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM – Error correction code (ECC) – Flexible write and read protection modes – In-application and in-circuit programming – Data EEPROM capability – 1.5 Kbytes of static RAM • Clock management – Internal 16 MHz RC with fast wakeup time (typ. 4 µs) – Internal low consumption 38 kHz RC driving both the IWDG and the AWU • Reset and supply management – Ultra-low power POR/PDR – Three low-power modes: Wait, Active-halt, Halt • Interrupt management – Nested interrupt controller with software priority control – Up to 29 external interrupt sources • I/Os – Up to 30 I/Os, all mappable on external interrupt vectors – I/Os with programmable input pull-ups, high sink/source capability and one LED driver infrared output May 2017 This is information on a product in full production. UFQFPN32 5 x 5 mm UFQFPN28 4 x 4 mm LQFP32 7x7 mm TSSOP20 6.5 x 6.4 mm UFQFPN20 3 x 3 mm • Peripherals – Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM) – One 8-bit timer (TIM4) with 7-bit prescaler – Infrared remote control (IR) – Independent watchdog – Auto-wakeup unit – Beeper timer with 1, 2 or 4 kHz frequencies – SPI synchronous serial interface – Fast I2C Multimaster/slave 400 kHz – USART with fractional baud rate generator – 2 comparators with 4 inputs each • Development support – Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging – In-circuit emulation (ICE) • 96-bit unique ID Table 1. Device summary Reference Part numbers STM8L101x1 STM8L101F1 STM8L101x2 STM8L101F2, STM8L101G2 STM8L101x3 STM8L101F3, STM8L101G3, STM8L101K3 DocID15275 Rev 16 1/88 www.st.com PDF
Документация на STM8L101F2U6TR 

8-bit ultra-low power microcontroller with up to 8 Kbytes Flash, multifunction timers, comparators, USART, SPI, I2C

Дата модификации: 12.05.2017

Размер: 2.05 Мб

88 стр.

STM8L101xx 8-bit ultralow power microcontroller with up to 8 Kbytes Flash, multifunction timers, comparators, USART, SPI, I2C Datasheet - production data Features • Main microcontroller features – Supply voltage range 1.65 V to 3.6 V – Low power consumption (Halt: 0.3 µA, Active-halt: 0.8 µA, Dynamic Run: 150 µA/MHz) – STM8 Core with up to 16 CISC MIPS throughput – Temp. range: -40 to 85 °C and 125 °C • Memories – Up to 8 Kbytes of Flash program including up to 2 Kbytes of data EEPROM – Error correction code (ECC) – Flexible write and read protection modes – In-application and in-circuit programming – Data EEPROM capability – 1.5 Kbytes of static RAM • Clock management – Internal 16 MHz RC with fast wakeup time (typ. 4 µs) – Internal low consumption 38 kHz RC driving both the IWDG and the AWU • Reset and supply management – Ultralow power POR/PDR – Three low power modes: Wait, Active-halt, Halt • Interrupt management – Nested interrupt controller with software priority control – Up to 29 external interrupt sources • I/Os – Up to 30 I/Os, all mappable on external interrupt vectors – I/Os with prog. input pull-ups, high sink/source capability and one LED driver infrared output August 2013 This is information on a product in full production. UFQFPN32 UFQFPN28 LQFP32 UFQFPN20 TSSOP20 • Peripherals – Two 16-bit general purpose timers (TIM2 and TIM3) with up and down counter and 2 channels (used as IC, OC, PWM) – One 8-bit timer (TIM4) with 7-bit prescaler – Infrared remote control (IR) – Independent watchdog – Auto-wakeup unit – Beeper timer with 1, 2 or 4 kHz frequencies – SPI synchronous serial interface – Fast I2C Multimaster/slave 400 kHz – USART with fractional baud rate generator – 2 comparators with 4 inputs each • Development support – Hardware single wire interface module (SWIM) for fast on-chip programming and non intrusive debugging – In-circuit emulation (ICE) • 96-bit unique ID Table 1. Device summary Reference STM8L101xx DocID15275 Rev 12 Part numbers STM8L101F1, STM8L101F2, STM8L101F3, STM8L101G2, STM8L101G3 STM8L101K3 1/83 www.st.com PDF
Документация на серию STM8L101G3 

8-bit ultralow power microcontroller with up to 8 Kbytes Flash, multifunction timers, comparators, USART, SPI, I2C

Дата модификации: 06.08.2013

Размер: 1.72 Мб

83 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.