2187687-1

Application Specification 114-32029 3.9-mm Pitch 85-Ohm, 92-Ohm and 100-Ohm STRADA Whisper* Connector System O1FEB2021 REV.Y NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless other wise specified, dimensions have a tolerance of ±0.13 and angles have a tolerance of ±2°. Figures are not drawn to scale. 1. INTRODUCTION...
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Семейство
Стандарт/Применение
Тип разъема
Количество контактов
Шаг между контактами
Рабочее напряжение контактов
Рабочий ток контактов
Тип монтажа
Расположение контактов разъема
  Примечания: STRADA Whisper 3.9mm, High Speed Backplane Connectors, Board-to-Board, 76 Position, Row-to-Row Spacing 2.5 mm [.098 in], Mating Alignment
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 4

показать свернуть
Application Specification 114-32029 3.9-mm Pitch 85-Ohm, 92-Ohm and 100-Ohm STRADA Whisper* Connector System O1FEB2021 REV.Y NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters. Unless other wise specified, dimensions have a tolerance of ±0.13 and angles have a tolerance of ±2°. Figures are not drawn to scale. 1. INTRODUCTION This specification covers the requirements for application of the 3.9-mm pitch 85-ohm, 92-Ohm and 100-ohm STRADA Whisper connector system. The connector system uses a modular concept and interconnects two printed circuit (pc) boards. The connectors are available in double-end wall (DEW) and open-end (OE) vertical press-fit pin header and right-angle and vertical press-fit receptacle connected to the pc board via eye-ofneedle (EON) compliant pin press-fit contacts. Differential pairs are arranged pair in-row (PiR) or pair in-column (PiC) depending on the application. Available connector sizes are given in Figure 1. When mating, connector alignment features help align contacts prior to engagement of the connectors. For PiR connectors, the header alignment bosses fit into the receptacle alignment slots, which have a guide feature. For PiC connectors, receptacle alignment bosses fit into the pin header alignment slots with a guide feature. In addition, universal guide hardware is available and should be used with the connectors to provide error-free mating and prevent damage to the connector housings and contacts. The female guide module and male guide pin are designed to be installed onto the pc board. These guides are also recommended for multiconnector, large and heavy daughtercard applications, and conditions where the misalignment tolerances cannot be met. The male guide pin is available with internal or external threading. Keyed versions of the guide pin and module are also available Basic terms and features of this product are provided in Figure 1. PiR Connectors DEW Vertical Pin Header (66 Shown) OE Vertical Pin Header (66 Shown) Right-Angle Receptacle (66 Shown) Chicklet Alignment Slot (2 Places) Differential Signal Pair “C” Ground Pin Flat Ground Pin Alignment Boss (2 Places) CONNECTOR SIZE PiR PiC 46 46 63 4 66 66 76 67 78 68 84 0611 86 0612 88 88 96 0810 98 0812 1260 0816 Pin 1 Indicator Mated Assembly Right-Angle Receptacle EON Compliant Pin Press-Fit Contacts STRADA Whisper Connector Guides With Standoff Internal Threaded Male Guide Pin Standoff Female Guide Module DEW Vertical Pin Header (Ref) Figure 1 (Con’td) © 2021 TE Connectivity family of companies All Rights Reserved *Trademark PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 34 PDF
Документация на 2187799-1 

Дата модификации: 09.02.2021

Размер: 7.81 Мб

34 стр.

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 2017 6 5 4 3 2 1 2017 RELEASED FOR PUBLICATION REVISIONS ALL RIGHTS RESERVED. BY TE CONNECTIVITY P D DWN APVD 1 PROPOSED 17NOV2016 JM RP B REVISED TO ECO-17-004845 28APR2017 AP RP C REVISED PER ECO-19-008905 11JUN2019 AP RP D REVISED PER ECO-20-008922 30JUN2020 AP RP 2 FINISH: MATING AREA: 1.25um MIN GOLD OVER 1.25um MIN NICKEL UNDERPLATE OVER ENTIRE CONTACT. COMPLIANT PIN AREA: . 0.5um MIN TIN-LEAD 3 GROUND PLATED THRU HOLE REQUIREMENTS: FINISHED HOLE = n 0.37 # 0.05 HOLE SIZE PRIOR TO PLATING = n 0.450 # 0.025 COPPER THICKNESS = 0.025 MIN 0.05um MIN GOLD OVER 3um-6um NICKEL 4 SIGNAL PLATED THRU HOLE REQUIREMENTS: FINISHED HOLE = n 0.29 # 0.05 HOLE SIZE PRIOR TO PLATING = n 0.368 # 0.025 (#79 DRILL) COPPER THICKNESS = 0.025 MIN 0.05um MIN GOLD OVER 3um-6um NICKEL 5 SI VIA PLATED THRU HOLE REQUIREMENTS: FINISHED HOLE = (n 0.22) HOLE SIZE PRIOR TO PLATING = n 0.300 # 0.025 COPPER THICKNESS = 0.025 MIN 0.05um MIN GOLD OVER 3um-6um NICKEL 6 SIGNAL HOLES AND SI VIAS: PTH DIMENSIONS APPLY TO THE TOP 1.00mm OF THE PCB THICKNESS FROM THE CONNECTOR MOUNTING SIDE. GROUND HOLES: PTH DIMENSIONS APPLY TO THE TOP 1.25mm OF THE PCB THICKNESS FROM THE CONNECTOR MOUNTING SIDE. 7 CONNECTOR MARKED WITH PART NUMBER, DATE CODE, AND "85 OHM" IN APPROXIMATE AREA SHOWN. 8 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER 9 APPLIES TO FINISHED HOLE DIAMETER 10 ( 16.1 ) DATE CONTACTS AND SHIELDS - COPPER ALLOY ORGANIZER - STAINLESS STEEL HOUSING, GROUND SHELLS, AND PIN SPACER - THERMOPLASTIC, UL 94V-0, BLACK C FRONT HOUSING DESCRIPTION 1 ORGANIZER CLIP GROUND SHIELD HOUSING TYP LTR D C DATAMATRIX BARCODE MARKING IN THIS AREA. ( 28.79 ) 12 11 9 8 6 5 SHIELD TYP 3 2 F B B E D ( 18.25 ) C B A ( 3.9 ) TYP ( 2.5 ) TYP 10 PIN SPACER ORGANIZER SIGNAL CONTACT A2 ( 0.98 ) BEFORE SEATING (1.88) AFTER SEATING SIGNAL CONTACT A2 ( 0.5 ) A ( 15.1 ) BEFORE SEATING (14.2) AFTER SEATING 7 ( 10.05 ) 2187687-1 ( 2.0 ) PART NO THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/13) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 1 0.13 - 2 - DWN 13JAN2017 CHK 13JAN2017 APVD 13JAN2017 J.McCLINTON R.PATTERSON R.PATTERSON TE Connectivity NAME PRODUCT SPEC 108-32021 APPLICATION SPEC - 114-32029 WEIGHT - CUSTOMER DRAWING A SIZE RIGHT ANGLE RECEPTACLE ASSEMBLY, 6 PAIR 4 COLUMN, 85 OHM, PAIR-IN-ROW, STRADA WHISPER A1 CAGE CODE 00779 DRAWING NO 2187687 SCALE 6:1 SHEET 1 OF RESTRICTED TO SPACE MICRO 2 REV D PDF
Документация на 2187687-1 

Дата модификации: 01.07.2020

Размер: 647.4 Кб

2 стр.

Product Specification 108-32021 22FEB2018 REV K 3.9mm STRADA Whisper* PIR & PIC 85-Ohm, 92-Ohm & 100-Ohm Connector Systems 1. SCOPE 1.1. Content This specification defines performance, tests and quality requirements for the 3.9mm STRADA Whisper Connector System, that uses a modular concept to interconnect two printed circuit boards. Both receptacle and pin connectors are connected to the printed circuit board with plated thru-hole compliant press-fit leads. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity (TE) Documents      2.2. 114-32029: Application Specification (3.9mm STRADA Whisper Connector System) 501-134055: Qualification Test Report (3.9mm 85Ω PIC STRADA Whisper Connector System) NOTE: 92-Ohm PIC is the same physical geometry as 85-Ohm PIC and is covered by this report. 501-134061: Qualification Test Report (3.9mm 85Ω PIR STRADA Whisper Connector System) NOTE: 92-Ohm PIR is the same physical geometry as 85-Ohm PIR and is covered by this report. 501-134064: Qualification Test Report (3.9mm 100Ω PIR STRADA Whisper Connector System) 501-134068: Qualification Test Report (3.9mm 100Ω PIC STRADA Whisper Connector System) Industry Standard EIA-364: 2.3. Electrical Connector/Socket Test Procedures Including Environmental Classifications Reference Document 109-197: Test Specification (TE Test Specifications vs. EIA and IEC Test Methods) 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction, materials and physical dimensions specified on the applicable product drawing. 3.2. Ratings    Voltage: Current: Temperature: © 2018 TE Connectivity family of companies All Rights Reserved | Indicates Change 80 volts AC maximum peak (⅓ of minimum withstanding voltage) See Figure 2 -55 to 105°C This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com PRODUCT INFORMATION 1-800-522-6752 *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 6 PDF
Документация на 1-2057754-3 

Дата модификации: 23.02.2018

Размер: 202.2 Кб

6 стр.

Product Specification 108-2351 19 AUG 16 Rev H1 IMPACT 100 Ohm Interconnect Systems 1. SCOPE 1.1. Content This specification defines the performance, tests and quality requirements for the TE Connectivity (TE) IMPACT 100 Ohm Interconnect Systems which consists of modular groupings of broad-edge coupled signals with optional integrated guidance. These connectors are two-piece devices, which connect two printed circuit boards (PCBs). The right angle receptacle connectors (daughtercard) and header pin connectors (backplane) are through-hole devices with Eye-of-the-Needle (EON) compliant pin terminals. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. Successful qualification testing on the subject product line was completed on 25 Feb 11. The Qualification Test Report number for this testing is 501-743. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity Document 501-743: IMPACT Interconnect Systems (Qualification Test Report) 2.2. Industry Document EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications 2.3. Reference Document 109-197: TE Test Specifications vs. EIA and IEC Test Methods (Test Specification) 2.4. The header pins are lubricated in the contact area with an approved lubricant according to industry standard Telcordia GR-1217-CORE, Section 5.3. 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. IMPACT and Molex are trademarks of Molex, Incorporated © 2016 TE Connectivity family of companies All Rights Reserved | Indicates Change *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 8 PDF
Документация на 2110186-3 

IMPACT 100 Ohm Interconnect Syatems

Дата модификации: 19.08.2016

Размер: 197.9 Кб

8 стр.

    Публикации 4

    показать свернуть
    04 октября
    статья

    Умнее, быстрее, плотнее! Решения TE Connectivity для сетей 5G

    Святослав Зубарев (г. Смоленск) Значительная часть производственной линейки компании TE Connectivity – изделия для подключения и развертывания сетей 5G. В статье рассматриваются также основные проблемы, с которыми сталкиваются разработчики при... ...читать

    05 июля 2021
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Перспективные решения для серверов и дата-центров

    Святослав Зубарев (г. Смоленск) Вторая часть серии публикаций о решениях компании TE Connectivity для высокоскоростных соединений посвящена соединителям и кабельным сборкам, ориентированным на применение в серверах и дата–центрах. Это... ...читать

    25 мая 2021
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Соединители STRADA Whisper

    Святослав Зубарев (г. Смоленск) Данная статья является первой из публикаций, описывающих решения компании TE Connectivity для высокоскоростных соединений. Она посвящена соединителям и кабельным сборкам серии STRADA Whisper, главная особенность... ...читать

    31 августа 2015
    MultiGIG
    новость

    Разъемы для высокоскоростных модульных систем от TE Connectivity

    Вычислительные комплексы с модульной архитектурой давно стали стандартом в телекоммуникациях и IT–оборудовании. К системам на основе «материнской» платы и «модулей расширения» предъявляются самые разнообразные требования и одним из основных... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.