2198174-1

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 TE CONNECTIVITY RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR DESCRIPTION DATE DWN APVD A RELEASED PER ECO-17-009578 05JUL2017 JM DT B REVISED PER ECO-19-011912 05AUG2019 AP RP ( 29.91 ) 1 D GROUND SHIELD HOUSING 24X 2 CONFORMS TO REQUIREMENTS OF TE PRODUCT SPECI...
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Семейство
Стандарт/Применение
Тип разъема
Количество контактов
Шаг между контактами
Рабочее напряжение контактов
Рабочий ток контактов
Тип монтажа
Расположение контактов разъема
  Примечания: STRADA Whisper 3.9mm, High Speed Backplane Connectors, Board-to-Board, 144 Position, Row-to-Row Spacing 3.9 mm [.154 in], Mating Alignment
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 6

показать свернуть
7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 TE CONNECTIVITY RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. 1 REVISIONS DIST 00 P LTR DESCRIPTION DATE DWN APVD A RELEASED PER ECO-17-009578 05JUL2017 JM DT B REVISED PER ECO-19-011912 05AUG2019 AP RP ( 29.91 ) 1 D GROUND SHIELD HOUSING 24X 2 CONFORMS TO REQUIREMENTS OF TE PRODUCT SPECIFICATION 108-32021, BASED ON TELCORDIA GR-1217-CORE FOR SYSTEM QUALITY LEVEL III APPLICATIONS IN CONTROLLED ENVIRONMENTS (CENTRAL OFFICE). 3 PLATED THRU HOLE REQUIREMENTS -GROUND AND SI: FINISHED HOLE = n 0.37 # 0.05 DRILLED HOLE = n 0.450 # 0.025 COPPER THICKNESS = 0.025 MIN IMMERSION TIN IF APPLICABLE = (0.00095) 4 PLATED THRU HOLE REQUIREMENTS -SIGNAL: FINISHED HOLE = n 0.24 # 0.04 DRILLED HOLE = n 0.320 # 0.025 COPPER THICKNESS = 0.025 MIN IMMERSION TIN IF APPLICABLE = (0.00095) 5 SIGNAL PLATED OF PCB GROUND PLATED OF PCB FRONT HOUSING ( 10.05 ) C CONTACTS - COPPER ALLOY. CLIP - STAINLESS STEEL, HOUSINGS AND ORGANIZER - THERMOPLASTIC, UL 94V-0, BLACK. HOLES: THRU HOLE THICKNESS HOLES: THRU HOLE THICKNESS D DIMENSIONS APPLY TO THE TOP 1.00 MOUNTING SIDE FROM THE CONNECTOR MOUNTING SIDE. DIMENSIONS APPLY TO THE TOP 1.25 MOUNTING SIDE FROM THE CONNECTOR MOUNTING SIDE. 6 DATUMS AND BASIC DIMENSIONS ESTABLISHED BY CUSTOMER. 7 CONNECTOR MARKED ON EITHER SIDE OF HOUSING WITH PART NUMBER, DATE CODE, AND "100 OHM" IN APPROXIMATE AREA SHOWN. C ( 40.95 ) ( 34.05 ) CLIP M L K J H G F E D C B A SIGNAL CONTACT PAIR 72X 18 17 15 14 B ( 26.3 ) GROUND CONTACTS TYP 12 11 7 9 8 6 5 ( 3.9 ) TYP 3 2 ( 1.1 ) TYP ( 2.5 ) TYP SIGNAL CONTACT A2 B ( 25.15 ) BEFORE SEATING (24.25) AFTER SEATING TYP DataMatrix BARCODE ( 1.35 ) BEFORE SEATING (2.25) AFTER SEATING TYP ORGANIZER ( 1.05 ) TYP ( 11.05 ) ( 0.8 ) BEFORE SEATING (1.7) AFTER SEATING TYP ( 2.0 ) TYP A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 4805 (3/11) - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.25 0.20 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH 1 - DWN 12AUG2011 CHK 12AUG2011 APVD 12AUG2011 J.McCLINTON J.McCLELLAN J.McCLELLAN PRODUCT SPEC NAME APPLICATION SPEC - 114-32029 WEIGHT - CUSTOMER DRAWING 2198174-1 PRESS-FIT TAIL PLATING PART NO A TE Connectivity 2 - TIN SIZE RECEPTACLE ASSEMBLY, RIGHT ANGLE, 6 PAIR 12 COLUMN, 100 OHM PiC, STRADA WHISPER CAGE CODE A1 00779 DRAWING NO RESTRICTED TO 2198174 SCALE 4:1 SHEET 1 OF - 2 REV B PDF
Документация на 2198174-1 

Дата модификации: 05.08.2019

Размер: 1.4 Мб

2 стр.

3.9-mm Pitch 85-Ohm and 100-Ohm Co-Planar (CP) and Direct Plug Orthogonal (DPO) STRADA Whisper* Connector System Application Specification 114-32120 22 MAY 18 Rev F NOTE All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and inches]. Unless otherwise specified, dimensions have a tolerance of ±0.13 [±.005] and angles have a tolerance of ±2°. Figures and illustrations are for identification only and are not drawn to scale. 1. INTRODUCTION This specification covers the requirements for application of 3.9-mm pitch 85-ohm and 100-ohm CP and DPO STRADA Whisper connector system. This connector system uses a modular concept and interconnects two printed circuit (pc) boards. The connectors are available in CP and DPO header assemblies. Each header assembly consists of a vertical plug and a right-angle receptacle that connect to the pc board via eye-of-needle (EON) compliant pin press-fit contacts. The differential pair contacts are arranged pair in-row (PiR) or pair incolumn (PiC). These header assemblies mate to standard receptacles having the same contact arrangement. When corresponding with personnel, use the terminology provided in this specification to facilitate inquiries for information. Basic terms and features of this product are provided in Figure 1. PiR CP Header Assembly Latch (Amount Varies) PiR Right-Angle Receptacle PiR DPO Header Assembly Key Slot (2 Places) Key (2 Places) Key Slot (2 Places) Vertical Plug EON Compliant Pin Press-Fit Contacts Pin 1 Indicator PiR-to-PiR Mated Assembly CP Header Assembly PiC Right-Angle Receptacle Key (2 Places) Right-Angle Receptacle PiC-to-PiR Mated Assembly DPO Header Assembly Guides Right-Angle Guide Pin PiR Right-Angle Receptacle Female Guide Module PC Right-Angle Receptacle Figure 1 © 2018 TE Connectivity family of companies All Rights Reserved *Trademark TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 19 PDF
Документация на 2304069-1 

Дата модификации: 22.05.2018

Размер: 7.65 Мб

19 стр.

Product Specification 108-32021 22FEB2018 REV K 3.9mm STRADA Whisper* PIR & PIC 85-Ohm, 92-Ohm & 100-Ohm Connector Systems 1. SCOPE 1.1. Content This specification defines performance, tests and quality requirements for the 3.9mm STRADA Whisper Connector System, that uses a modular concept to interconnect two printed circuit boards. Both receptacle and pin connectors are connected to the printed circuit board with plated thru-hole compliant press-fit leads. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity (TE) Documents      2.2. 114-32029: Application Specification (3.9mm STRADA Whisper Connector System) 501-134055: Qualification Test Report (3.9mm 85Ω PIC STRADA Whisper Connector System) NOTE: 92-Ohm PIC is the same physical geometry as 85-Ohm PIC and is covered by this report. 501-134061: Qualification Test Report (3.9mm 85Ω PIR STRADA Whisper Connector System) NOTE: 92-Ohm PIR is the same physical geometry as 85-Ohm PIR and is covered by this report. 501-134064: Qualification Test Report (3.9mm 100Ω PIR STRADA Whisper Connector System) 501-134068: Qualification Test Report (3.9mm 100Ω PIC STRADA Whisper Connector System) Industry Standard EIA-364: 2.3. Electrical Connector/Socket Test Procedures Including Environmental Classifications Reference Document 109-197: Test Specification (TE Test Specifications vs. EIA and IEC Test Methods) 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction, materials and physical dimensions specified on the applicable product drawing. 3.2. Ratings    Voltage: Current: Temperature: © 2018 TE Connectivity family of companies All Rights Reserved | Indicates Change 80 volts AC maximum peak (⅓ of minimum withstanding voltage) See Figure 2 -55 to 105°C This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com PRODUCT INFORMATION 1-800-522-6752 *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 6 PDF
Документация на 1-2057754-3 

Дата модификации: 23.02.2018

Размер: 202.2 Кб

6 стр.

Документация на 2198174-1 

c-2198174-1

Дата модификации: 31.08.2017

Размер: 875 Кб

1 стр.

Product Specification 108-2351 19 AUG 16 Rev H1 IMPACT 100 Ohm Interconnect Systems 1. SCOPE 1.1. Content This specification defines the performance, tests and quality requirements for the TE Connectivity (TE) IMPACT 100 Ohm Interconnect Systems which consists of modular groupings of broad-edge coupled signals with optional integrated guidance. These connectors are two-piece devices, which connect two printed circuit boards (PCBs). The right angle receptacle connectors (daughtercard) and header pin connectors (backplane) are through-hole devices with Eye-of-the-Needle (EON) compliant pin terminals. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. Successful qualification testing on the subject product line was completed on 25 Feb 11. The Qualification Test Report number for this testing is 501-743. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity Document 501-743: IMPACT Interconnect Systems (Qualification Test Report) 2.2. Industry Document EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications 2.3. Reference Document 109-197: TE Test Specifications vs. EIA and IEC Test Methods (Test Specification) 2.4. The header pins are lubricated in the contact area with an approved lubricant according to industry standard Telcordia GR-1217-CORE, Section 5.3. 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. IMPACT and Molex are trademarks of Molex, Incorporated © 2016 TE Connectivity family of companies All Rights Reserved | Indicates Change *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 8 PDF
Документация на 2110186-3 

IMPACT 100 Ohm Interconnect Syatems

Дата модификации: 19.08.2016

Размер: 197.9 Кб

8 стр.

    Публикации 3

    показать свернуть
    05 июля
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Перспективные решения для серверов и дата-центров

    Святослав Зубарев (г. Смоленск) Вторая часть серии публикаций о решениях компании TE Connectivity для высокоскоростных соединений посвящена соединителям и кабельным сборкам, ориентированным на применение в серверах и дата–центрах. Это... ...читать

    25 мая 2021
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Соединители STRADA Whisper

    Святослав Зубарев (г. Смоленск) Данная статья является первой из публикаций, описывающих решения компании TE Connectivity для высокоскоростных соединений. Она посвящена соединителям и кабельным сборкам серии STRADA Whisper, главная особенность... ...читать

    31 августа 2015
    MultiGIG
    новость

    Разъемы для высокоскоростных модульных систем от TE Connectivity

    Вычислительные комплексы с модульной архитектурой давно стали стандартом в телекоммуникациях и IT–оборудовании. К системам на основе «материнской» платы и «модулей расширения» предъявляются самые разнообразные требования и одним из основных... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.