2274854-1

Технические характеристики

показать свернуть
Семейство
Стандарт/Применение
Тип разъема
Количество контактов
Шаг между контактами
Рабочее напряжение контактов
Рабочий ток контактов
Тип монтажа
Расположение контактов разъема
  Примечания: STRADA Whisper 3.9mm, High Speed Backplane Connectors, Board-to-Board, 48 Position, Row-to-Row Spacing 3.9 mm [.154 in], Mating Alignment
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 5

показать свернуть
Документация на 2274854-1 

c-2274854-1

Дата модификации: 08.08.2018

Размер: 565.5 Кб

1 стр.

Product Specification 108-32021 22FEB2018 REV K 3.9mm STRADA Whisper* PIR & PIC 85-Ohm, 92-Ohm & 100-Ohm Connector Systems 1. SCOPE 1.1. Content This specification defines performance, tests and quality requirements for the 3.9mm STRADA Whisper Connector System, that uses a modular concept to interconnect two printed circuit boards. Both receptacle and pin connectors are connected to the printed circuit board with plated thru-hole compliant press-fit leads. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity (TE) Documents      2.2. 114-32029: Application Specification (3.9mm STRADA Whisper Connector System) 501-134055: Qualification Test Report (3.9mm 85Ω PIC STRADA Whisper Connector System) NOTE: 92-Ohm PIC is the same physical geometry as 85-Ohm PIC and is covered by this report. 501-134061: Qualification Test Report (3.9mm 85Ω PIR STRADA Whisper Connector System) NOTE: 92-Ohm PIR is the same physical geometry as 85-Ohm PIR and is covered by this report. 501-134064: Qualification Test Report (3.9mm 100Ω PIR STRADA Whisper Connector System) 501-134068: Qualification Test Report (3.9mm 100Ω PIC STRADA Whisper Connector System) Industry Standard EIA-364: 2.3. Electrical Connector/Socket Test Procedures Including Environmental Classifications Reference Document 109-197: Test Specification (TE Test Specifications vs. EIA and IEC Test Methods) 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction, materials and physical dimensions specified on the applicable product drawing. 3.2. Ratings    Voltage: Current: Temperature: © 2018 TE Connectivity family of companies All Rights Reserved | Indicates Change 80 volts AC maximum peak (⅓ of minimum withstanding voltage) See Figure 2 -55 to 105°C This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com PRODUCT INFORMATION 1-800-522-6752 *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 6 PDF
Документация на 1-2057754-3 

Дата модификации: 23.02.2018

Размер: 202.2 Кб

6 стр.

7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION 6 5 4 3 2 20 LOC GP ALL RIGHTS RESERVED. BY - TE CONECTIVITY B C D E 00 P LTR DESCRIPTION DATE DWN APVD A RELEASED 09MAY2016 Y.K D.T B REVISED PER ECR-17-013331 rev_date_2 JM DT HOUSING:THERMOPLASTIC, BLACK. CONTACTS: COPPER ALLOY. 2 CONFORMS TO REQUIREMENTS OF TE PRODUCT SPECIFICATION 108-32021 BASED ON TELCORDIA GR-1217-CORE FOR SYSTEM QUALITY LEVEL III APPLICATIONS IN CONTROLLED ENVIRONMENTS (CENTRAL OFFICE). D 3 PLATED THRU HOLE FINISHED HOLE = DRILLED HOLE = COPPER THICKNESS IMMERSION TIN IF REQUIREMENTS: n 0.32 # 0.05 n 0.400 # 0.025 = 0.025 MIN. APPLICABLE = 0.0006-0.0011 4 PLATED THRU HOLE DIMENSIONS APPLY TO THE TOP 1.25mm DEPTH FROM MOUNT SIDE OF PC BOARD. 5 DATUMS AND BASICS DIMENSIONS ESTABLISHED BY CUSTOMER. 6 CONNECTOR MARKED ON EITHER SIDE OF HOUSING WITH PART NUMBER AND DATE CODE IN APPROXIMATE AREA SHOWN. ( 1.45 ) SIGNAL CONTACT 6 F REVISIONS DIST 1 D A 1 C C SIGNAL CONTACTS TYP -- 12 -- 11 GROUND CONTACTS TYP -- 9 -- 8 B 0.12 -- 6 -- 5 ( 3.9 ) TYP POSITION A1 CORNER INDICATOR 21.00 -- 3 -- 2 ( 1.65 ) ( 2.5 ) TYP +0.1 18.1 -0.2 B ( 1.5 ) 11.50 0.15 A THIS DRAWING IS A CONTROLLED DOCUMENT. DIMENSIONS: mm MATERIAL 0.10 - 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - 1 4805 (3/11) TOLERANCES UNLESS OTHERWISE SPECIFIED: - DWN 09MAY2016 CHK 09MAY2016 APVD 09MAY2016 Y.KODAIRA D.TROUT D.TROUT PRODUCT SPEC 2 APPLICATION SPEC - - WEIGHT TIN 2274854-1 PRESS-FIT TAIL PLATING PART NUMBER TE Connectivity NAME HEADER ASSEMBLY, 4 PAIR 6 COLUMN, 85 OHM PIC, STRADA WHISPER - SIZE - CUSTOMER DRAWING A CAGE CODE A1 00779 DRAWING NO 2274854 SCALE 5:1 SHEET 1 RESTRICTED TO OF - 2 REV B PDF
Документация на 2274854-1 

Дата модификации: 13.09.2017

Размер: 1.04 Мб

2 стр.

Product Specification 108-2351 19 AUG 16 Rev H1 IMPACT 100 Ohm Interconnect Systems 1. SCOPE 1.1. Content This specification defines the performance, tests and quality requirements for the TE Connectivity (TE) IMPACT 100 Ohm Interconnect Systems which consists of modular groupings of broad-edge coupled signals with optional integrated guidance. These connectors are two-piece devices, which connect two printed circuit boards (PCBs). The right angle receptacle connectors (daughtercard) and header pin connectors (backplane) are through-hole devices with Eye-of-the-Needle (EON) compliant pin terminals. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. Successful qualification testing on the subject product line was completed on 25 Feb 11. The Qualification Test Report number for this testing is 501-743. This documentation is on file at and available from Engineering Practices and Standards (EPS). 2. APPLICABLE DOCUMENTS The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the latest edition of the document applies. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence. In the event of conflict between the requirements of this specification and the referenced documents, this specification shall take precedence. 2.1. TE Connectivity Document 501-743: IMPACT Interconnect Systems (Qualification Test Report) 2.2. Industry Document EIA-364: Electrical Connector/Socket Test Procedures Including Environmental Classifications 2.3. Reference Document 109-197: TE Test Specifications vs. EIA and IEC Test Methods (Test Specification) 2.4. The header pins are lubricated in the contact area with an approved lubricant according to industry standard Telcordia GR-1217-CORE, Section 5.3. 3. REQUIREMENTS 3.1. Design and Construction Product shall be of the design, construction and physical dimensions specified on the applicable product drawing. IMPACT and Molex are trademarks of Molex, Incorporated © 2016 TE Connectivity family of companies All Rights Reserved | Indicates Change *Trademark. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 1 of 8 PDF
Документация на 2110186-3 

IMPACT 100 Ohm Interconnect Syatems

Дата модификации: 19.08.2016

Размер: 197.9 Кб

8 стр.

    Публикации 3

    показать свернуть
    05 июля
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Перспективные решения для серверов и дата-центров

    Святослав Зубарев (г. Смоленск) Вторая часть серии публикаций о решениях компании TE Connectivity для высокоскоростных соединений посвящена соединителям и кабельным сборкам, ориентированным на применение в серверах и дата–центрах. Это... ...читать

    25 мая 2021
    статья

    Решения TE Connectivity для 112 Gbps архитектуры и серверов. Соединители STRADA Whisper

    Святослав Зубарев (г. Смоленск) Данная статья является первой из публикаций, описывающих решения компании TE Connectivity для высокоскоростных соединений. Она посвящена соединителям и кабельным сборкам серии STRADA Whisper, главная особенность... ...читать

    31 августа 2015
    MultiGIG
    новость

    Разъемы для высокоскоростных модульных систем от TE Connectivity

    Вычислительные комплексы с модульной архитектурой давно стали стандартом в телекоммуникациях и IT–оборудовании. К системам на основе «материнской» платы и «модулей расширения» предъявляются самые разнообразные требования и одним из основных... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.