TEL 8-2410WI

TRACO
Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing...
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Напряжение 1 выхода
Ток 1 выхода
Напряжение изоляции вход-выход
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 26

показать свернуть
Тип Наименование Корпус Упаковка i Монтаж P вых Каналов U вх Выход Возможности Защита U вх ном. U1 U2 U3 I1 I2 I3 Шум КПД Паралл. сх. Uиз. вх-вых Uиз. вх-общ Uиз. вых-общ Uиз. вых-вых Серт. медиц. T раб Примечания Карточка
товара
A- TEL 10-2410WI (TRACO)
 
2 шт
 
A- RSDW08F-03 (MW)
 
КЗ, перегрузка, перенапряжение, от пониженного входного напряжения
A- DDR-15G-3.3 (MW)
 
1 шт КЗ, переполюсовки, пониженного входного напряжения
A- NSD10-12S3 (MW)
 
2X1INCH 1 шт DC-DC модульный преобразователь - Монтаж: на плату, 2x1 inch; P вых: 10 Вт; #: 1; U вх:... перегрузки, перенапряжения, перегрева EN55024, light industry level, criteria A
A- VRB1203ZP-10WR3 (MORNSUN)
 
в линейках 10 шт
A- VRB2403ZP-10WR3 (MORNSUN)
 
в линейках 20 шт
 
A- URB2403ZP-10WR3 (MORNSUN)
 
в линейках 20 шт
 
A- TEN 8-1210 (TRACO)
 
DIP2410 в линейках 10 шт DC-DC модульный преобразователь - Монтаж: на плату, DIP24; P вых: 8 Вт; #: 1; U вх: 9..... короткого замыкания, перегрузки Защита от КЗ: продолжительная с автовосстановлением
A- TEN 8-2410 (TRACO)
 
DIP2410 в линейках 10 шт DC-DC модульный преобразователь - Монтаж: на плату, DIP24; P вых: 8 Вт; #: 1; U вх: 18.... короткого замыкания, перегрузки Защита от КЗ: продолжительная с автовосстановлением
A- TEN 8-2410WI (TRACO)
 
DIP2410 в линейках 10 шт DC-DC модульный преобразователь - Монтаж: на плату, DIP24; P вых: 8 Вт; #: 1; U вх: 9..... короткого замыкания, перегрузки Защита от КЗ: продолжительная с автовосстановлением
A- THD 12-2410 (TRACO)
 
DIP2410 в линейках 10 шт DC-DC модульный преобразователь - Монтаж: на плату, DIP24; P вых: 12 Вт; #: 1; U вх: 18... Защита от КЗ: продолжительная с автовосстановлением
A- NSD10-48S3 (MW)
 
2X1INCH 1 шт DC-DC модульный преобразователь - Монтаж: на плату, 2x1 inch; P вых: 10 Вт; #: 1; U вх:... перегрузки, перенапряжения, перегрева EN55024, light industry level, criteria A
A- RSDW08G-03 (MW)
 
КЗ, перегрузка, перенапряжение, от пониженного входного напряжения
A- SKM10A-03 (MW)
 
12 шт короткого замыкания, перегрузки, перенапряжения, пониженного входного напряжения
A- SKM10B-03 (MW)
 
короткого замыкания, перегрузки, перенапряжения, пониженного входного напряжения
A- SKM10C-03 (MW)
 
короткого замыкания, перегрузки, перенапряжения, пониженного входного напряжения
A- SKM10E-03 (MW)
 
короткого замыкания, перегрузки, перенапряжения, пониженного входного напряжения
A- SKMW15F-03 (MW)
 
 
DC-DC Regulated Power Supply Module
A- SKMW15G-03 (MW)
 
 
DC-DC Regulated Power Supply Module
A- URF2403LP-10WR3 (MORNSUN)
 
2X1INCH 11 шт
 
A- URF2403LP-10WR3A2S (MORNSUN)
 
 
A- URF2403LP-10WR3A4S (MORNSUN)
 
 
A- URF4803LP-10WR3 (MORNSUN)
 
2X1INCH
 
A- URF4803LP-10WR3A2S (MORNSUN)
 
 
A- URF4803LP-10WR3A4S (MORNSUN)
 
 
A- VRB4803YMD-10WR3 (MORNSUN)
 
 

Файлы 1

показать свернуть
Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services PDF
Рекомендации по промывке и сушке 

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.