TEN 30-2408WI

TRACO
DC/DC конвертор: PCB 2"x1.6"; 30 Вт; Выход 1.8В / 8А; Вход: 10...40 [24] В; -40...85 °C
развернуть ▼ свернуть ▲
Фотография серии TEN30WI
Чертеж серии TEN30WI
 
 

Технические характеристики

показать свернуть
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Возможности
Комплекс защит короткого замыкания, перенапряжения, перегрева
Номинальное входное напряжение
Напряжение 1 выхода
Ток 1 выхода
Уровень пульсаций
КПД
Напряжение изоляции вход-выход
Размер 50.8×40.6×10.2 мм
Рабочая температура
Примечания Защита от КЗ: продолжительная с автовосстановлением
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 3

показать свернуть
Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services PDF
Рекомендации по промывке и сушке 

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

DC/DC Converters TEN 30WI Series, 30 Watt Features ◆ Ultra wide 4:1 input voltage range ◆ Single output voltage models from 1.8 to 15 VDC ◆ Dual output voltage models ◆ Extended operating temperature range: –40°C to 85°C ◆ Under voltage lockout ◆ Remote On/Off ◆ Shielded metal case with insulated baseplate ◆ Optional heatsink ◆ Lead free design - RoHS compliant ◆ 3-year product warranty The TEN 30WI series is a family of high performance 30W dc-dc converters featuring ultra wide 4:1 input voltage ranges in a compact low profile package with industry-standard footprint. A very high efficiency allows operating temperatures up to 85°C. A built-in filter for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. TEN 30-2408WI 1.8 VDC 8‘000 mA 80 % TEN 30-2409WI 2.5 VDC 8’000 mA 85 % TEN 30-2410WI 3.3 VDC 6’000 mA 87 % TEN 30-2411WI 10 – 40 VDC 5.0 VDC 6‘000 mA 87 % TEN 30-2412WI (nominal 24 VDC) 12 VDC 2’500 mA 87 % TEN 30-2413WI 15 VDC 2’000 mA 88 % TEN 30-2422WI ±12 VDC ±1’250 mA 85 % TEN 30-2423WI ±15 VDC ±1’000 mA 86 % TEN 30-4808WI 1.8 VDC 8‘000 mA 81 % TEN 30-4809WI 2.5 VDC 8’000 mA 86 % TEN 30-4810WI 3.3 VDC 6’000 mA 87 % TEN 30-4811WI 18 – 75 VDC 5.0 VDC 6‘000 mA 88 % TEN 30-4812WI (nominal 48 VDC) 12 VDC 2’500 mA 87 % TEN 30-4813WI 15 VDC 2’000 mA 88 % TEN 30-4822WI ±12 VDC ±1’250 mA 86 % TEN 30-4823WI ±15 VDC ±1’000 mA 87 % http://www.tracopower.com Page 1 of 4 PDF
Документация на серию TEN30WI 

TEN30WI

Дата модификации: 20.04.2012

Размер: 154.4 Кб

4 стр.

DC/DC Converters TEN 30WI Series, 30 Watt RoHS compliant Features ◆ High Power Density: 30W in a 51x41x10 mm (2”x1.6”x0.4”) Package ◆ Ultra Wide 4:1 Input Voltage Range ◆ Single Output Voltage Models from 1.8 to 15 VDC ◆ Dual Output Voltage Models ◆ Extended Operating Temperature Range: –40°C to 85°C ◆ Under Voltage Lockout ◆ Remote On/Off ◆ Shielded Metal Case with insulated Baseplate ◆ Optional Heatsink ◆ Lead free Design - RoHS compliant ◆ 3 Year Product Warranty The TEN 30WI series is a family of high performance 30W dc-dc converters featuring ultra wide 4:1 input voltage ranges in a compact low profile package with industry-standard footprint. A very high efficiency allows operating temperatures up to 85°C. A built-in filter for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code Output voltage Output current max. Efficiency typ. TEN 30-2408WI 1.8 VDC 8‘000 mA 80 % TEN 30-2409WI 2.5 VDC 8’000 mA 85 % TEN 30-2410WI 3.3 VDC 6’000 mA 87 % TEN 30-2411WI 5.0 VDC 6‘000 mA 87 % 12 VDC 2’500 mA 87 % TEN 30-2412WI Input voltage range 10 – 40 VDC TEN 30-2413WI 15 VDC 2’000 mA 88 % TEN 30-2422WI ± 12 VDC ± 1’250 mA 85 % TEN 30-2423WI ± 15 VDC ± 1’000 mA 86 % TEN 30-4808WI 1.8 VDC 8‘000 mA 81 % TEN 30-4809WI 2.5 VDC 8’000 mA 86 % TEN 30-4810WI 3.3 VDC 6’000 mA 87 % TEN 30-4811WI 5.0 VDC 6‘000 mA 88 % 12 VDC 2’500 mA 87 % TEN 30-4812WI 18 – 75 VDC TEN 30-4813WI 15 VDC 2’000 mA 88 % TEN 30-4822WI ± 12 VDC ± 1’250 mA 86 % TEN 30-4823WI ± 15 VDC ± 1’000 mA 87 % http://www.tracopower.com Page  of 7 PDF
Документация на серию TEN30WI 

TEN30WI

Дата модификации: 07.08.2006

Размер: 139.4 Кб

7 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    DCH010505SN7 (TI)