TEN 40-1210

DC/DC конвертор: 40 Вт; корпус PCB 2x2 inch; выход 3.3В @ 8А; вход: 9...18 [12] В; -40...85 °C; изоляция вх-вых: 1.5 кВ

Группа: DC-DC модульные преобразователи
Серия: TEN40
Корпус: 2X2INCH
Норма упаковки: 5 шт. (в линейках)

шт в корзину копировать сравнитьтовар в списке сравнения

Технические характеристики

показать свернуть

	Монтаж
	Выходная мощность
	Количество каналов
	Входное напряжение
	Параметры выходов
	Возможности
	Комплекс защит	короткого замыкания, перенапряжения, перегрева
	Номинальное входное напряжение
	Напряжение 1 выхода
	Ток 1 выхода
	Уровень пульсаций
	КПД
	Схема параллельного включения
	Напряжение изоляции вход-выход
	Сертификаты медицинские
	Размер	50.8×50.8×10.16 мм
	Рабочая температура
	Примечания	Защита от КЗ: продолжительная с автовосстановлением

Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги ²⁰

показать свернуть

Тип	Наименование	Корпус	Упаковка	Защита	U2	U3	I2	I3	Шум	КПД	Паралл. сх.	Uиз. вх-общ	Uиз. вых-общ	Uиз. вых-вых	Серт. медиц.	Примечания
A-	TEN 50-2410WI (TRACO)	2X1INCH			—	—	—	—			—	—	—	—	—	—
A-	TEN 40-2433 (TRACO)	2X2INCH	1 шт	короткого замыкания, перенапряжения, перегрева							—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением. Указаны шумы на первом выходе
A-	RSDW40F-03 (MW)	—	1 шт	КЗ, перегрузка, перенапряжение, от пониженного входного напряжения	—	—	—	—	—			—	—	—		—
A-	RSDW40G-03 (MW)	—		КЗ, перегрузка, перенапряжение, от пониженного входного напряжения	—	—	—	—	—			—	—	—		—
A-	RSDW60F-03 (MW)	—		КЗ, перегрузка, перенапряжение, от пониженного входного напряжения	—	—	—	—	—			—	—	—		—
A-	RSDW60G-03 (MW)	—		КЗ, перегрузка, перенапряжение, от пониженного входного напряжения	—	—	—	—	—			—	—	—		—
A-	TEN 50-1210 (TRACO)	2X1INCH	2 шт		—	—	—	—			—	—	—	—	—	—
A-	TEN 50-2410 (TRACO)	2X1INCH			—	—	—	—			—	—	—	—	—	—
A-	RP40-243.3SGW (RECOM)	2X2INCH	в линейках 4 шт		—	—	—	—	—	—		—	—	—		—
A-	TEN 40-1210E (TRACO)	—			—	—	—	—	—		—	—	—	—	—	—
A-	TEN 60-2410 (TRACO)	2X2INCH	1 шт		—	—	—	—			—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением
A-	TEN 40-1220 (TRACO)	2X2INCH	в линейках 5 шт	короткого замыкания, перенапряжения, перегрева		—		—			—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением
A-	TEN 40-2410E (TRACO)	—			—	—	—	—	—		—	—	—	—	—	—
A-	TEN 40-2410WI (TRACO)	2X2INCH	в линейках 5 шт		—	—	—	—				—	—	—		Защита от КЗ: продолжительная с автовосстановлением
A-	TEN 40-2410WIE (TRACO)	—			—	—	—	—	—		—	—	—	—	—	—
A-	TEN 40-2410WIR (TRACO)	2X1INCH	в линейках 10 шт	короткого замыкания, перенапряжения, перегрева	—	—	—	—			—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением
A-	TEN 40-4810WI (TRACO)	2X2INCH	в линейках 5 шт		—	—	—	—			—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением
A-	TEN 40-4810WIE (TRACO)	—			—	—	—	—	—		—	—	—	—	—	—
A-	TEN 40-4810WIR (TRACO)	2X1INCH	1 шт	короткого замыкания, перенапряжения, перегрева	—	—	—	—			—	—	—	—	—	Защита от КЗ: продолжительная с автовосстановлением
A-	RPA50S-483.3SW/P (RECOM)	—			—	—	—	—	—	—		—	—	—		—

Файлы ⁵

показать свернуть

DC/DC Converter TEN 40 Series, 40 Watt • • • 40 Watt in a 2”x2” package • Over temperature protection, under voltage lockout and Remote On/Off • Shielded metal case with insulated baseplate • Wide 2:1 input voltage range Extended operating temperature range: –40°C to +75°C UL 62368-1 IEC 62368-1 The TEN 40 series is a family of high performance 40W DC/DC converter modules featuring a wide 2:1 input voltage range in a 2"x2" package. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics. 3-years product warranty Models Order Code Input Voltage Range TEN 40-1210 TEN 40-1211 TEN 40-1212 TEN 40-1220 TEN 40-1222 TEN 40-1223 TEN 40-1233 TEN 40-1234 TEN 40-1231 TEN 40-1232 TEN 40-2410 TEN 40-2411 TEN 40-2412 TEN 40-2420 TEN 40-2422 TEN 40-2423 TEN 40-2433 TEN 40-2434 TEN 40-2431 TEN 40-2432 TEN 40-4810 TEN 40-4811 TEN 40-4812 TEN 40-4820 TEN 40-4822 TEN 40-4823 TEN 40-4833 TEN 40-4834 TEN 40-4831 TEN 40-4832 9 - 18 VDC (12 VDC nom.) 18 - 36 VDC (24 VDC nom.) 36 - 75 VDC (48 VDC nom.) Output 1 Vnom Imax 3.3 VDC 5 VDC 12 VDC +3.3 VDC +12 VDC +15 VDC +3.3 VDC +3.3 VDC +5 VDC +5 VDC 3.3 VDC 5 VDC 12 VDC +3.3 VDC +12 VDC +15 VDC +3.3 VDC +3.3 VDC +5 VDC +5 VDC 3.3 VDC 5 VDC 12 VDC +3.3 VDC +12 VDC +15 VDC +3.3 VDC +3.3 VDC +5 VDC +5 VDC 8'000 mA 8'000 mA 3'300 mA 8'000 mA 1'800 mA 1'400 mA 6'000 mA 6'000 mA 6'000 mA 6'000 mA 8'000 mA 8'000 mA 3'300 mA 8'000 mA 1'800 mA 1'400 mA 6'000 mA 6'000 mA 6'000 mA 6'000 mA 8'000 mA 8'000 mA 3'300 mA 8'000 mA 1'800 mA 1'400 mA 6'000 mA 6'000 mA 6'000 mA 6'000 mA Output 2 Vnom Imax Output 3 Vnom Imax +5 VDC –12 VDC –15 VDC +12 VDC +15 VDC +12 VDC +15 VDC 8'000 mA 1'800 mA 1'400 mA 400 mA 300 mA 400 mA 300 mA –12 VDC –15 VDC –12 VDC –15 VDC 400 mA 300 mA 400 mA 300 mA +5 VDC –12 VDC –15 VDC +12 VDC +15 VDC +12 VDC +15 VDC 8'000 mA 1'800 mA 1'400 mA 400 mA 300 mA 400 mA 300 mA –12 VDC –15 VDC –12 VDC –15 VDC 400 mA 300 mA 400 mA 300 mA +5 VDC –12 VDC –15 VDC +12 VDC +15 VDC +12 VDC +15 VDC 8'000 mA 1'800 mA 1'400 mA 400 mA 300 mA 400 mA 300 mA –12 VDC –15 VDC –12 VDC –15 VDC 400 mA 300 mA 400 mA 300 mA Efficiency typ. 86 % 86 % 86 % 85 % 85 % 85 % 84 % 84 % 86 % 86 % 87 % 89 % 88 % 86 % 87 % 87 % 85 % 85 % 87 % 87 % 88 % 90 % 89 % 88 % 87 % 87 % 86 % 86 % 88 % 88 % Options TEN-HS3 Note - Optional Heat Sink: www.tracopower.com/products/ten-hs3.pdf - TEN 40-xx20: Dynamic current allocation, 8 A total output current for both outputs together www.tracopower.com January 25, 2022 Page 1 / 6

PDF

Документация на TEN 40-1210

TEN 40 Datasheet 40 Watt DC/DC converter, industrial, 2:1 input, encapsulated, single- dual- tripple output, 2" x 2" metal package

Дата модификации: 25.01.2022

Размер: 942.8 Кб

6 стр.

DC/DC Converters TEN 40 Series, 40 Watt Features ◆ High power density: 40 W in a 51x51x10mm (2”x2”x0.4”) package ◆ Wide 2:1 input voltage range ◆ Models with single-, dual- and triple output ◆ Models with 2 independently regulated 3.3 and 5.0 VDC outputs ◆ Extended operating temperature range: –40°C to +75°C ◆ ◆ ◆ ◆ Over temperature protection Under voltage lockout Remote On/Off Shielded metal case with insulated baseplate ◆ Optional heatsink ◆ Lead free design - RoHS compliant ◆ 3-years product warranty The TEN 40 series is a family of high performance 40W dc-dc converter modules featuring 30 standard models with wide 2:1 input voltage ranges in a compact low profile case with industry-standard footprint. A very high efficiency allows an operating temperature range of –40°C to +75°C. Built-in filters for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code TEN 40-1210 TEN 40-1211 TEN 40-1212 TEN 40-1220 TEN 40-1222 TEN 40-1223 TEN 40-1233 TEN 40-1234 TEN 40-1231 TEN 40-1232 TEN 40-2410 TEN 40-2411 TEN 40-2412 TEN 40-2420 TEN 40-2422 TEN 40-2423 TEN 40-2433 TEN 40-2434 TEN 40-2431 TEN 40-2432 TEN 40-4810 TEN 40-4811 TEN 40-4812 TEN 40-4820 TEN 40-4822 TEN 40-4823 TEN 40-4833 TEN 40-4834 TEN 40-4831 TEN 40-4832 Note Input voltage range 9 – 18 VDC (nominal 12 VDC) 18 – 36 VDC (nominal 24 VDC) 36 – 75 VDC (nominal 48 VDC) Output 1 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A Output 2 Output 3 *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A Efficiency typ.. 86 % 86 % 86 % 85 % 85 % 85 % 84 % 84 % 86 % 86 % 87 % 89 % 88 % 86 % 87 % 87 % 85 % 85 % 87 % 87 % 88 % 90 % 89 % 88 % 87 % 87 % 86 % 86 % 88 % 88 % - Multi output models have a common ground. http://www.tracopower.com * dynamic current allocation, max. 8A total output current for both outputs together Page 1 of 4

PDF

Документация на TEN 40-1210

TEN40

Дата модификации: 25.08.2021

Размер: 283.5 Кб

4 стр.

Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services

PDF

Рекомендации по промывке и сушке

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

DC/DC Converters TEN 40 Series, 40 Watt Features ◆ High power density: 40 W in a 51x51x10mm (2”x2”x0.4”) package ◆ Wide 2:1 input voltage range ◆ Models with single-, dual- and triple output ◆ Models with 2 independently regulated 3.3 and 5.0 VDC outputs ◆ Extended operating temperature range: –40°C to +75°C ◆ ◆ ◆ ◆ Over temperature protection Under voltage lockout Remote On/Off Shielded metal case with insulated baseplate ◆ Optional heatsink ◆ Lead free design - RoHS compliant ◆ 3-years product warranty The TEN 40 series is a family of high performance 40W dc-dc converter modules featuring 30 standard models with wide 2:1 input voltage ranges in a compact low profile case with industry-standard footprint. A very high efficiency allows an operating temperature range of –40°C to +75°C. Built-in filters for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code TEN 40-1210 TEN 40-1211 TEN 40-1212 TEN 40-1220 TEN 40-1222 TEN 40-1223 TEN 40-1233 TEN 40-1234 TEN 40-1231 TEN 40-1232 TEN 40-2410 TEN 40-2411 TEN 40-2412 TEN 40-2420 TEN 40-2422 TEN 40-2423 TEN 40-2433 TEN 40-2434 TEN 40-2431 TEN 40-2432 TEN 40-4810 TEN 40-4811 TEN 40-4812 TEN 40-4820 TEN 40-4822 TEN 40-4823 TEN 40-4833 TEN 40-4834 TEN 40-4831 TEN 40-4832 Input voltage range 9 – 18 VDC (nominal 12 VDC) 18 – 36 VDC (nominal 24 VDC) 36 – 75 VDC (nominal 48 VDC) http://www.tracopower.com Output 1 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A Output 2 Output 3 *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A * dynamic current allocation, max. 8A total output current for both outputs together Efficiency typ.. 86 % 86 % 86 % 85 % 85 % 85 % 84 % 84 % 86 % 86 % 87 % 89 % 88 % 86 % 87 % 87 % 85 % 85 % 87 % 87 % 88 % 90 % 89 % 88 % 87 % 87 % 86 % 86 % 88 % 88 % Page 1 of 4

PDF

Документация на серию TEN40

TEN40

Дата модификации: 02.11.2012

Размер: 244 Кб

4 стр.

DC/DC Converters TEN 40 Series, 40 Watt Features ◆ High Power Density: 40W in a RoHS compliant 51x51x10mm (2”x2”x0.4”) Package ◆ Wide 2:1 Input Voltage Range ◆ Models with Single-, Dual- and Triple Output ◆ Models with 2 independently regulated 3.3 and 5.0 VDC Outputs ◆ Extended Operating Temperature Range: –40°C to +85°C ◆ ◆ ◆ ◆ Over Temperature Protection Under Voltage Lockout Remote On/Off Shielded metal Case with insulated Baseplate ◆ Optional Heatsink ◆ Lead free Design - RoHS compliant ◆ 3 Years Product Warranty The TEN 40 series is a family of high performance 40W dc-dc converter modules featuring 30 standard models with wide 2:1 input voltage ranges in a compact low profile case with industry-standard footprint. A very high efficiency allows an operating temperature range of –40°C to 85°C. Built-in filters for both input and output minimizes the need for external filtering. Further standard features include remote On/Off, output voltage trimming, over voltage protection, under voltage lockout and short circuit protection. Typical applications for these products are battery operated equipment and distributed power architectures in communication and industrial electronics, everywhere where isolated, tightly regulated voltages are required and space is limited on the PCB. Models Order code TEN 40-1210 TEN 40-1211 TEN 40-1212 TEN 40-1220 TEN 40-1222 TEN 40-1223 TEN 40-1233 TEN 40-1234 TEN 40-1231 TEN 40-1232 TEN 40-2410 TEN 40-2411 TEN 40-2412 TEN 40-2420 TEN 40-2422 TEN 40-2423 TEN 40-2433 TEN 40-2434 TEN 40-2431 TEN 40-2432 TEN 40-4810 TEN 40-4811 TEN 40-4812 TEN 40-4820 TEN 40-4822 TEN 40-4823 TEN 40-4833 TEN 40-4834 TEN 40-4831 TEN 40-4832 Input voltage range 9 – 18 VDC 18 – 36 VDC 36 – 75 VDC http://www.tracopower.com Output 1 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A 3.3 VDC / 8.0 A 5 VDC / 8.0 A 12 VDC / 3.3 A *3.3 VDC / 8.0 A +12 VDC / 1.8 A +15 VDC / 1.4 A 3.3 VDC / 6.0 A 3.3 VDC / 6.0 A 5 VDC / 6.0 A 5 VDC / 6.0 A Output 2 Output 3 *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A *5 VDC / 8.0 A –12 VDC / 1.8 A –15 VDC / 1.4 A +12 VDC / 0.4 A +15 VDC / 0.3 A +12 VDC / 0.4 A +15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A –12 VDC / 0.4 A –15 VDC / 0.3 A * dynamic current allocation, max. 8A total output current for both outputs together Efficiency typ.. 86 % 86 % 86 % 85 % 85 % 85 % 84 % 84 % 86 % 86 % 87 % 89 % 88 % 86 % 87 % 87 % 85 % 85 % 87 % 87 % 88 % 90 % 89 % 88 % 87 % 87 % 86 % 86 % 88 % 88 % Page of 9

PDF

Документация на серию TEN40

TEN40

Дата модификации: 14.07.2006

Размер: 180.5 Кб

9 стр.

найти TEN 40-1210.pdf

Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

DKA30C-15 (MW) DDR-120A-12 (MW)

TEN 40-1210

Технические характеристики

Аналоги 20

Файлы 5

Аналоги ²⁰

Файлы ⁵