TEP 150-2412WI

DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 150 Вт; #: 1; U вх: 9...36 В; Выход: 12 В; Возможности: дистанционное управление
развернуть ▼ свернуть ▲

Технические характеристики

показать свернуть
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Возможности
Комплекс защит
Номинальное входное напряжение
Напряжение 1 выхода
Ток 1 выхода
Уровень пульсаций
КПД
Напряжение изоляции вход-выход
Размер 61×65×35.7 мм
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 17

показать свернуть
Тип Наименование Корпус Упаковка i Монтаж P вых Каналов U вх Выход Возможности Защита U вх ном. U1 U2 U3 I1 I2 I3 Шум КПД Паралл. сх. Uиз. вх-вых Uиз. вх-общ Uиз. вых-общ Uиз. вых-вых Серт. медиц. T раб Примечания Карточка
товара
A- TEP 160-2412WIR (TRACO) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 160 Вт; #: 1; U вх: 8.5...36...
A- RSD-150B-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 150 Вт; #: 1; U вх: 16.8...3... короткого замыкания, перегрузки, перенапряжения, переполюсовки
A- RSD-150C-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 151 Вт; #: 1; U вх: 33.6...6... короткого замыкания, перегрузки, перенапряжения, переполюсовки
A- RSD-200B-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 200 Вт; #: 1; U вх: 16.8...3... короткого замыкания, перегрузки, перенапряжения, переполюсовки
A- RSD-200C-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 200 Вт; #: 1; U вх: 33.6...6... короткого замыкания, перегрузки, перенапряжения, переполюсовки
A- DDR-120B-12 (MW) в коробках 28 шт КЗ, переполюсовки, пониженного входного напряжения
A- DDR-120C-12 (MW) в коробках 3 шт КЗ, переполюсовки, пониженного входного напряжения
A- TEP 150-4812WI (TRACO) 1 шт CONVERTER, DC DC, 150W, 12V, 12.5A
A- TEP 160-4812WIR (TRACO) 1 шт короткого замыкания, перегрузки, перегрева
A- TEQ 200-4812WIR (TRACO) КЗ, перегрев, перенапряжение, от пониженного входного напряжения
A- MHB150-48S12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: на плату; P вых: 150 Вт; #: 1; U вх: 36...75 ... короткого замыкания, перегрузки, перенапряжения
A- SD-150B-12 (MW) 1 шт короткого замыкания, перегрузки, перенапряжения
A- SD-150C-12 (MW) в коробках 16 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 150 Вт; #: 1; U вх: 36...72 ... короткого замыкания, перегрузки, перенапряжения
A- SD-200B-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 200 Вт; #: 1; U вх: 19...36 ... короткого замыкания, перегрузки, перенапряжения, перегрева
A- SD-200C-12 (MW) 1 шт DC-DC модульный преобразователь - Монтаж: в кожухе; P вых: 200 Вт; #: 1; U вх: 36...72 ... короткого замыкания, перегрузки, перенапряжения, перегрева
A- RPA150Q-11012SRUW/P (RECOM) DC-DC Regulated Power Supply Module короткого замыкания, перенапряжения, перегрева
A- IRQ-12/12.5-W80NB-C (MUR)
 

Файлы 4

показать свернуть
DC/DC Railway Converter • Shielded metal case with screw terminals • Ultra wide 4:1 input voltage ranges 9–36, 18–75, 43–160 VDC • EN 50155 approval for railway applications • • Very high efficiency up to 89% • Optional with input filter to meet EN 55032 class B TEP 150WI Series, 150 Watt Constant current output characteristic for battery load applications • Wide Operating temperature range: –40°C to +75°C • Under voltage lock-out, overtemperature & reverse input protection • • Easy chassis and wall mounting 3-year product warranty UL 62368-1 IEC 62368-1 The modules have originally been designed for harsh industrial environment. High EMC immunity against surge, burst, radiated and conducted disturbances and the shock/ vibration and thermal shock resistance make them very popular for stringent requirements. With the extended input voltage ranges that cover the nominal 24, 36, 72 and 110 VDC with ±40 % tolerance and the approval in accordance to EN 50155 standard they now also offer a reliable solution for mobile and stationary railway applications. At 100% load the current characteristics goes from constant voltage to constant current what makes the units also suitable for battery charger applications. With protection against over-temperature, overload, short-circuit, reverse input, overvoltage and input under-voltage lock-out they are hard to destroy. Models Order Code Input Voltage Range Output Voltage nom. Output Current max. Efficiency typ. TEP 150-2412WI 12 VDC 12'500 mA 86 % TEP 150-2413WI 15 VDC 10'000 mA 86 % 9 - 36 VDC (24 VDC nom.) 24 VDC 6'300 mA 87 % TEP 150-2416WI 28 VDC 5'400 mA 87 % TEP 150-2418WI 48 VDC 3'200 mA 86 % TEP 150-4812WI 12 VDC 12'500 mA 88 % TEP 150-4813WI 15 VDC 10'000 mA 89 % 24 VDC 6'300 mA 89 % TEP 150-4816WI 28 VDC 5'400 mA 89 % TEP 150-4818WI 48 VDC 3'200 mA 88 % TEP 150-7212WI 12 VDC 12'500 mA 88 % TEP 150-7213WI 15 VDC 10'000 mA 89 % 24 VDC 6'300 mA 89 % TEP 150-7216WI 28 VDC 5'400 mA 89 % TEP 150-7218WI 48 VDC 3'200 mA 88 % TEP 150-2415WI TEP 150-4815WI TEP 150-7215WI www.tracopower.com 18 - 75 VDC (48 VDC nom.) 43 - 160 VDC (110 VDC nom.) October 14, 2021 Page 1 / 5 PDF
Документация на TEP 150-2412WI 

TEP 150WI Datasheet 150 Watt DC/DC module, railway, 4:1 input, Chassis mount, Rugged design, opt. EMI Filter, encapsulated, High power block

Дата модификации: 14.10.2021

Размер: 983.3 Кб

5 стр.

Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services PDF
Рекомендации по промывке и сушке 

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

DC/DC Converters TEP 150WI Series, 150 Watt CB UL 60950-1 Scheme Features ◆ Shielded metal case with screw terminals ◆ Compact dimensions: 98 x 52 x 34 mm ◆ Ultra-wide 4:1 input voltage range ◆ Very high efficiency up to 87% ◆ Constant current output characteristic for battery load applications ◆ Optional with input filter to meet EN55022 class B ◆ Overtemperature protection ◆ Wide Operating temperature range: –40°C to +75°C ◆ ◆ ◆ ◆ ◆ Reverse input protection Under voltage lock-out I/O isolation 2250 VDC Easy chassis and wall mounting 3-year product warranty The TEP-150WI Series is a family of high power density dc-dc converter modules with ultra-wide 4:1 input voltage range which come in an ultra-compact metal case with screw terminal connection. Suitable for a wide range of applications, the TEP-150WI series was particularly designed with industrial applications in mind. The modules have flanges for easy chassis or wall mounting. A very high efficiency allows an operating temperature up to +50°C with natural convection cooling. Further features include adjustable output voltage with constant current characteristic for battery charger applications. Models Order code* Input voltage Output voltage Output current max. Efficiency typ. TEP 150-2412WI 12 VDC 12.5 A 86 % TEP 150-2413WI 15 VDC 10 A 86 % 24 VDC 6.3 A 87 % 9 – 36 VDC TEP 150-2415WI (24 VDC nominal) TEP 150-2416WI 28 VDC 5.4 A 87 % TEP 150-2418WI 48 VDC 3.2 A 86 % TEP 150-4812WI 12 VDC 12.5 A 87 % 15 VDC 10 A 87 % 24 VDC 6.3 A 88 % TEP 150-4813WI 18 – 75 VDC TEP 150-4815WI (48 VDC nominal) TEP 150-4816WI 28 VDC 5.4 A 88 % TEP 150-4818WI 48 VDC 3.2 A 87 % TEP 150-7212WI 12 VDC 12.5 A 86 % 15 VDC 10 A 86 % 24 VDC 6.3 A 87 % 28 VDC 5.4 A 87 % 48 VDC 3.2 A 86 % TEP 150-7213WI 43 – 160 VDC TEP 150-7215WI (72 VDC nominal) TEP 150-7216WI TEP 150-7218WI Options suffix –F on demand Modules with input filter to meet EN 55022 class B, see page 5 Negative (passive = Off) remote On/Off function (standard is passive = On)range http://www.tracopower.com Page 1 of 5 PDF
Документация на серию TEP150WI 

datasheet

Дата модификации: 14.06.2013

Размер: 615.2 Кб

5 стр.

DC/DC Converters TEP 150WI Series, 150 Watt CB Scheme Features ◆ Shielded metal case with screw terminals ◆ Compact dimensions: 98 x 52 x 34 mm ◆ Ultra-wide 4:1 input voltage range ◆ Very high efficiency up to 87% ◆ Constant current output characteristic for UL 60950-1 battery load applications ◆ Optional with input filter to meet EN55022 class B ◆ Overtemperature protection ◆ Wide Operating temperature range: –40°C to +75°C ◆ ◆ ◆ ◆ ◆ Reverse input protection Under voltage lock-out I/O isolation 2250 VDC Easy chassis and wall mounting 3-year product warranty The TEP-150WI Series is a family of high power density dc-dc converter modules with ultra-wide 4:1 input voltage range which come in an ultra-compact metal case with screw terminal connection. Suitable for a wide range of applications, the TEP-150WI series was particularly designed with industrial applications in mind. The modules have flanges for easy chassis or wall mounting. A very high efficiency allows an operating temperature up to +50°C with natural convection cooling. Further features include adjustable output voltage with constant current characteristic for battery charger applications. Models Order code* Input voltage Output voltage Output current max. Efficiency typ. TEP 150-2412WI 12 VDC 12.5 A 86 % TEP 150-2413WI 15 VDC 10 A 86 % 24 VDC 6.3 A 87 % TEP 150-2416WI 28 VDC 5.4 A 87 % TEP 150-2418WI 48 VDC 3.2 A 86 % TEP 150-4812WI 12 VDC 12.5 A 87 % 15 VDC 10 A 87 % 24 VDC 6.3 A 88 % TEP 150-4816WI 28 VDC 5.4 A 88 % TEP 150-4818WI 48 VDC 3.2 A 87 % 9 – 36 VDC (24 VDC nominal) TEP 150-2415WI TEP 150-4813WI 18 – 75 VDC (48 VDC nominal) TEP 150-4815WI Options suffix –F on demand Modules with input filter to meet EN 55022 class B, see page 5 Negative (passive = Off) remote On/Off function (standard is passive = On) Models with input voltage range 43 – 160 VDC http://www.tracopower.com Page 1 of 5 PDF
Документация на серию TEP150WI 

TEN60

Дата модификации: 29.06.2012

Размер: 413.9 Кб

5 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.