Серия ethernet интерфейсов ADIN1300

Общие характеристики

Документация на серию ADIN1300

Robust, Industrial, Low Latency and Low Power 10 Mbps,100 Mbps, and 1 Gbps Ethernet PHY ADIN1300 Data Sheet FEATURES GENERAL DESCRIPTION 10BASE-Te/100BASE-TX/1000BASE-T IEEE® 802.3™ compliant MII, RMII, and RGMII MAC interfaces 1000BASE-T RGMII latency transmit < 68 ns, receive < 226 ns 100BASE-TX MII latency transmit< 52 ns, receive < 248 ns EMC test standards IEC 61000-4-5 surge (±4 kV) IEC 61000-4-4 electrical fast transient (EFT) (±4 kV) IEC 61000-4-2 ESD (±6 kV contact discharge) IEC 61000-4-6 conducted immunity (10 V) EN55032 radiated emissions (Class A) EN55032 conducted emissions (Class A) Unmanaged configuration using multilevel pin strapping EEE in accordance with IEEE 802.3az Start of packet detection for IEEE 1588 time stamp support Enhanced link detection Configurable LED Crystal oscillator frequency/25 MHz clock input frequency (50 MHz for RMII) 25 MHz/125 MHz synchronous clock output Small package and wide temperature range 40-lead, 6 mm × 6 mm LFCSP Specified for −40°C to +105°C ambient operation Low power consumption 330 mW for 1000BASE-T 140 mW for 100BASE-TX 3.3 V/2.5 V/1.8 V MAC interface VDDIO supply Integrated power supply monitoring and POR The ADIN1300 is a low power, single port, Gigabit Ethernet transceiver with low latency and power consumption specifications primarily designed for industrial Ethernet applications. APPLICATIONS Industrial automation Process control Factory automation Robotics/motion control Time sensitive networking (TSN) Building automation Test and measurement Industrial internet of things (IoT) Rev. 0 This design integrates an energy efficient Ethernet (EEE) physical layer device (PHY) core with all associated common analog circuitry, input and output clock buffering, management interface and subsystem registers, and MAC interface and control logic to manage the reset and clock control and pin configuration. The ADIN1300 is available in a 6 mm × 6 mm, 40-lead lead frame chip scale package (LFCSP). The device operates with a minimum of 2 power supplies, 0.9 V and 3.3 V, assuming the use of a 3.3 V MAC interface supply. For maximum flexibility in system level design, a separate VDDIO supply enables the management data input/output (MDIO) and MAC interface supply voltages to be configured independently of the other circuitry on the ADIN1300, allowing operation at 1.8 V, 2.5 V, or 3.3 V. At power-up, the ADIN1300 is held in hardware reset until each of the supplies has crossed its minimum rising threshold value. Brown-out protection is provided by monitoring the supplies to detect if one or more supply drops below a minimum falling threshold (see Table 17), and holding the device in hardware reset until the power supplies return and satisfy the power-on reset (POR) circuit. The MII management interface (also referred to as MDIO interface) provides a 2-wire serial interface between a host processor or MAC (also known as management station (STA)) and the ADIN1300, allowing access to control and status information in the PHY core management registers. The interface is compatible with both the IEEE 802.3 Standard Clause 22 and Clause 45 management frame structures. The ADIN1300 can support cable lengths up to 150 meters at Gigabit speeds and 180 meters when operating at 100 Mbps or 10 Mbps. Note that throughout this data sheet, multifunction pins, such as XTAL_I/CLK_IN/REF_CLK, are referred to either by the entire pin name or by a single function of the pin, for example, XTAL_I/CLK_IN, when only that function is relevant. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2019 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com PDF
Документация на серию ADIN1300 

ADIN1300 (Rev. 0) Robust, Industrial, Low Latency and Low Power 10 Mbps, 100 Mbps, and 1 Gbps Ethernet PHY

Дата модификации: 18.10.2019

Размер: 1.39 Мб

79 стр.

    Товары серии ADIN1300

    Наименование i Упаковка T раб
    ADIN1300BCPZ (AD)
    ADIN1300BCPZ-R7 (AD)
    ADIN1300CCPZ (AD) 4 шт
    ADIN1300CCPZ-R7 (AD)

    ADIN1300 публикации

    09 сентября

    ИС физического уровня 10/100/1000 Мбит/с промышленного двухканального Ethernet с низким энергопотреблением

    Микросхема физического уровня Ethernet с двумя каналами ADIN1300 производства Analog Devices идеальна для организации на производстве мониторинга, контроля и построения распределенных систем управления. Статья посвящена тестированию отладочной... ...читать

    14 апреля 2021

    Трансиверы ADIN1200 и ADIN1300 от Analog Devices для промышленного Ethernet

    Промышленный Ethernet предназначен для использования на производстве, где из–за тяжелых эксплуатационных условий часто требуются герметичные разъемы, стойкие к агрессивным средам кабели более высокого качества с улучшенным экранированием и... ...читать

    09 апреля 2021

    Решения Analog Devices для гальванической изоляции. Обзор технологий и новинок (материалы вебинара)

    Программа показатьсвернуть Приглашаем всех желающих принять участие в вебинаре, посвященном решениям Analog Devices для гальванической изоляции. Современное оборудование требует надежного уровня защиты и безопасности данных. Компоненты... ...читать