Серия LED-драйверов PLP-20

Общие характеристики

	Раздел	LED-драйверы
	Тип преобразователя
	Напряжение сети/входное номинальное
	Режим стабилизации
	Тип диммирования
	Исполнение конструктивное
	Степень защиты (IP)
	Подстройка выходных параметров
	Диапазон входных напряжений (AC)
	Диапазон входных напряжений (DC)
	Напряжение изоляции вход-выход
	Количество выходов
	Коэффициент мощности
	Функция защиты	КЗ, перегрузка, перенапряжение, перегрев
	Температура рабочая
	Размер	140×32×22 мм
	Применение

Документация на серию PLP-20

PLP-20 20W Single Output LED Power Supply series ■ Features : Universal AC input / Full range(up to 277VAC) Protections:Short circuit/Over current/Over voltage/Over temperature Cooling by free air convection Built-in constant current limiting circuit with adjustable OCP level Built-in active PFC function Class Ⅱ power unit, no FG Class 2 power unit Small and compact size 100% full load burn-in test High reliability,low cost Suitable for built-in applications of LED lighting 2 years warranty Bauar t gepruft Sicherheit egel ma ge od o s be wac g SPECIFICATION MODEL DC VOLTAGE PLP-20-12 PLP-20-18 PLP-20-24 PLP-20-36 PLP-20-48 12V 18V 24V 36V 48V 13.5 ~ 18V 18 ~ 24V 1.1A 0.8A 27 ~ 36V 0.55A 0.42A 0 ~ 1.1A 0 ~ 0.8A 0 ~ 0.55A 0 ~ 0.42A CONSTANT CURRENT REGION Note.5 9 ~ 12V 1.6A RATED CURRENT 0 ~ 1.6A CURRENT RANGE CURRENT ADJ. RANGE 75% ~ 100% 19.2W RATED POWER OUTPUT RIPPLE & NOISE (max.) Note.2 2.5Vp-p LINE REGULATION ±3.0% LOAD REGULATION ±10% 20.2W 3.8Vp-p 500ms / 230VAC 2000ms / 115VAC at full load 47 ~ 63Hz POWER FACTOR PF≥0.95/115VAC,PF>0.9/230VAC,PF>0.9/277VAC at full load (Please refer to "Power Factor Characteristic" curve) TOTAL HARMONIC DISTORTION EFFICIENCY(Typ.) THD< 20% when output loading≧75% at 115VAC/230VAC input and output loading≧75% at 277VAC input 83% 80% 83.5% 82% 81% AC CURRENT INRUSH CURRENT(Typ.) 0.4A/115VAC 0.2A/230VAC 0.15A/277VAC COLD START 25A(twidth=60μs measured at 50% Ipeak) at 230VAC MAX. No. of PSUs on 16A CIRCUIT BREAKER 92 units (circuit breaker of type B) / 98 units (circuit breaker of type C) at 230VAC 0.5mA / 240VAC Note.5 SHORT CIRCUIT OVER VOLTAGE 95 ~ 110% Protection type : Constant current limiting, recovers automatically after fault condition is removed Hiccup mode, recovers automatically after fault condition is removed. 27 ~ 34V 14 ~ 16V 19 ~ 22V Protection type : Shut off o/p voltage, clamping by zener diode OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. WORKING HUMIDITY -30 ~ +60℃ (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE SAFETY & ISOLATION RESISTANCE NOTE 19.8W 3.0Vp-p FREQUENCY RANGE OVER CURRENT OTHERS 19.2W 3.0Vp-p Note.4 90 ~ 277VAC 127~392VDC LEAKAGE CURRENT EMC 19.8W 3.0Vp-p L EO VOLTAGE RANGE PROTECTION 36 ~ 48V VOLTAGE TOLERANCE Note.3 ±10% SETUP, RISE TIME INPUT S&E www. tuv.com ID 2000000000 41 ~ 46V 54 ~ 60V 20 ~ 90% RH non-condensing -40 ~ +80℃, 10 ~ 95% RH ±0.06%/℃ (0 ~ 50℃) 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes TUV EN61347-1, EN61347-2-13, GB19510.14, GB19510.1, UL8750, CSA C22.2 No. 250.0-08,EAC TP TC 004 approved I/P-O/P:3.75KVAC I/P-O/P:100M Ohms/500VDC / 25℃/ 70%RH EMC EMISSION Compliance to EN55015, GB17743, GB17625.1, EN61000-3-2 Class C(≧75% load); EN61000-3-3,EAC TP TC 020 EMC IMMUNITY MTBF 643.6Khrs min. DIMENSION 140*32*22(L*W*H) PACKING 0.12kg;60pcs/9.2kg/0.62CUFT Compliance to EN61000-4-2,3,4,5,6,8,11, EN61547, light industry level, criteria A,EAC TP TC 020 MIL-HDBK-217F (25℃) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Derating may be needed under low input voltage, please check the static characteristic for more details. 5. Please refer to "DRIVING METHODS OF LED MODULE". 6. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to EMI testing of component power supplies. (as available on http://www.meanwell.com) 7. Direct connecting to LEDs is suggested, but is not suitable for using additional drivers. 8. To fulfill requirements of the latest ErP regulation for lighting fixtures, this LED power supply can only be used behind a switch without permanently connected to the mains. File Name:PLP-20-SPEC 2018-01-11

Документация на PLP-20-48

PLP-20.cdr

Дата модификации: 02.07.2019

Размер: 224.4 Кб

3 стр.

Документация на серию PLP-20

PLP-20.cdr

Дата модификации: 02.07.2010

Размер: 867.2 Кб

2 стр.

найти PLP-20.pdf

Товары серии PLP-20

Наименование	i	Упаковка	Мощность выходная	Напряжение выходное	Ток выходной	Эффективность
PLP-20-12 (MW)		1 шт
PLP-20-18 (MW)		1 шт
PLP-20-24 (MW)		1 шт
PLP-20-36 (MW)		1 шт
PLP-20-48 (MW)		1 шт

PLP-20 публикации

11 ноября 2009

новость

30 и 60 Вт источники питания для светодиодного освещения

На склад компании КОМПЭЛ поступили новые источники питания PLP для светодиодных светильников. Серия PLP выпускается в открытом исполнении и предназначена для монтажа внутрь корпуса светильника. Компания MEAN WELL производит две линейки источников... ...читать