Серия DC-DC модульных преобразователей TEN50WI

Общие характеристики

Раздел DC-DC модульные преобразователи
Монтаж
Выходная мощность
Количество каналов
Возможности
Комплекс защит
Уровень пульсаций
Напряжение изоляции вход-выход
Размер 50.8×25.4×11 мм
Рабочая температура

Документация на серию TEN50WI

Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services PDF
Рекомендации по промывке и сушке 

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

DC/DC Converters TEN 50WI Series, 50 Watt CB Features ◆ Very high power density: Scheme n pe g din 50 W in 1” x 2” x 0.4” package ◆ Wide 4:1 input range ◆ Excellent efficiency up to 92 % ◆ Operating temperature range –40°C to +80°C ◆ ◆ ◆ ◆ ◆ ◆ Protection against over-temperature No minimum load required Output voltage adjustable Remote On/Off I/O isolation 1500 VDC 3-year product warranty The TEN 50WI Series is a range of isolated high performance DC/DC converter modules. With a very high efficiency of up to 92% and the use of highest reliable components these 50 W converters can be packed into the standard 1.0” x 2.0” casing. The 10 models have a wide 4:1 input voltage range and a tight output voltage regulation. They do not need a minimum load and offer a high efficiency also at low load conditions. The output voltage is adjustable by external resistor. Remote On/Off and protection against overload and short circuit are standard features of these converters. Typical applications are in mobile equipment, instrumentation, distributed power architectures in communication and industrial electronics and everywhere where space on the PCB is critical. Models Order code Input voltage range Output voltage Output current max. Efficiency 3.3 VDC 10‘000 mA 90 % 5.0 VDC 10’000 mA 91 % 12 VDC 4‘170 mA 92 % 15 VDC 3‘330 mA 92 % TEN 50-2415WI 24 VDC 2‘080 mA 91 % TEN 50-4810WI 3.3 VDC 10‘000 mA 90 % 5.0 VDC 10’000 mA 91 % 12 VDC 4‘170 mA 92 % 15 VDC 3‘330 mA 92 % 24 VDC 2‘080 mA 91 % TEN 50-2410WI TEN 50-2411WI TEN 50-2412WI TEN 50-2413WI TEN 50-4811WI TEN 50-4812WI TEN 50-4813WI TEN 50-4815WI http://www.tracopower.com 9 – 36 VDC (nominal 24 VDC) 18 – 75 VDC (nominal 48 VDC) Page 1 of 4 PDF
Документация на серию TEN50WI 

Datasheet

Дата модификации: 21.02.2014

Размер: 193.7 Кб

4 стр.

    Товары серии TEN50WI

    Наименование i Упаковка U вх Выход U вх ном. U1 I1 КПД
    TEN 50-2410WI (TRACO)
    TEN 50-2411WI (TRACO) DC-DC модульный преобразователь - Монтаж: на плату, 2x1 inch; P вых: 50 Вт; #: 1; U вх:... в линейках 10 шт
    TEN 50-2412WI (TRACO) в линейках 10 шт
    TEN 50-2413WI (TRACO) в линейках 2 шт
    TEN 50-2415WI (TRACO) в линейках 10 шт
    TEN 50-4811WI (TRACO)
    TEN 50-4812WI (TRACO) 3 шт
    TEN 50-4813WI (TRACO)
    TEN 50-4815WI (TRACO)