Серия DC-DC модульных преобразователей THL 10

TRACO

Общие характеристики

 Раздел DC-DC модульные преобразователи
Монтаж
Выходная мощность
Возможности
Комплекс защит
Напряжение изоляции вход-выход
Размер 25.4×25.4×10.2 мм
Рабочая температура

Документация на серию THL 10

Baar, 11. December 2014 Cleaning Guideline Scope This guideline covers hermetically sealed board mounted Traco converters. We do not recommend washing insert moulded products, where it is difficult to get them dry inside. Please check also, if there is an additional comment about washing in the datasheet or application note of the concerned product. Note: We do generally not recommend washing or cleaning electronic components. You should avoid it, if it is not absolutely necessary. It may reduce the reliability of the involved components in your application. Board cooling prior to cleaning process Converters and their associated application PCB assemblies should not be wash-cleaned after soldering until they had the opportunity to cool within the cleaning solution temperature. This will prevent vacuum absorption of the cleaning liquid into the module between the pins and the potting during cooling. Cleaning agents Cleaning method Classification Cleaning agents Water type Deionized water Ultrasonic wave Solvent type IPA Note: In general, the liquid temperature shall be less than 60°C. Cleaning process In aqueous cleaning, it is preferred to have an in-line cleaner system consisting of several cleaning stages (prewash, wash, rinse, final rinse, and drying). Deionised (DI) water is recommended for aqueous cleaning; the minimum resistively level is 1MΩ-cm. Tap-water quality varies per region in terms of hardness, chloride, and solid contents. Therefore, the use of tap water is not recommended for aqueous cleaning. Note: The total time of ultrasonic wave shall be less than 3 minutes. Drying After cleaning, assure that everything will be dry enough, that the moisture and other potential contaminants will not be present anymore. Use an air circulating chamber (e.g. 0.5-0.7m3/s) and thermal oven at 80-100°C (during 20-120min, depending on assembling, structure, components). Handheld air guns are not recommended. It is on customer’s own responsibility to ensure all components are dry. Product post-wash external appearance The marking or date-code may fade or disappear after cleaning. That does not concern the performance of the converter. Andreas Flühler, Head of Technical Services PDF
Рекомендации по промывке и сушке 

Cleaning Guideline

Дата модификации: 02.02.2021

Размер: 79 Кб

1 стр.

DC/DC Converters THL 10 Series, 10 Watt Features ◆ 10 Watt in 1” x 1” package ◆ Shielded metal case with isolated ing nd e p CB Scheme 226037 UL 60950-1 UL 60950-1 baseplate ◆ Wide 2:1 input voltage ranges ◆ Operating temp. range –40°C to +80°C and up to +85°C with heat-sink ◆ I/O isolation voltage 1500 VDC ◆ Input filter meets EN 55022 class A without external components ◆ Cost optimized design ◆ Industry standard pinout ◆ 3-year product warranty The THL 10 is a series of general purpose 10 Watt dc/dc-converters packed in the compact 1” x 1” case and is a pin to pin replacement for the popular 1” x 2” size products. The industrial standard pinout, the wide 2:1 input voltage range and the input filter that meets EN 55022 Class A without external components make these converters easy to design in and suitable for to cost optimize many existing and new applications. The models have short circuit and overvoltage protection and are applicable in temperature ranges of up to +80°C or +85°C with optional mounted heat sink. Typical applications are instrumentation, distributed power architectures in communication and industrial electronics. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. THL 10-1210 3.3 VDC 2500 mA 82 % THL 10-1211 5.1 VDC 2000 mA 85 % THL 10-1212 12 VDC 830 mA 87 % THL 10-1213 9 – 18 VDC THL 10-1221 (12 VDC nominal) 15 VDC 670 mA 88 % ±5.0 VDC ±1000 mA 84 % THL 10-1222 ±12 VDC ±416 mA 87 % THL 10-1223 ±15 VDC ±333 mA 87 % THL 10-2410 3.3 VDC 2500 mA 83 % THL 10-2411 5.1 VDC 2000 mA 85 % THL 10-2412 12 VDC 830 mA 87 % 15 VDC 670 mA 89 % THL 10-2413 18 – 36 VDC THL 10-2421 (24 VDC nominal) ±5.0 VDC ±1000 mA 85 % THL 10-2422 ±12 VDC ±416 mA 88 % THL 10-2423 ±15 VDC ±333 mA 89 % THL 10-4810 3.3 VDC 2500 mA 83 % THL 10-4811 5.1 VDC 2000 mA 85 % 12 VDC 830 mA 89 % 15 VDC 670 mA 89 % ±5.0 VDC ±1000 mA 86 % THL 10-4822 ±12 VDC ±416 mA 87 % THL 10-4823 ±15 VDC ±333 mA 88 % THL 10-4812 THL 10-4813 36 – 75 VDC THL 10-4821 (48 VDC nominal) http://www.tracopower.com Page 1 of 4 PDF
Документация на серию THL 10 

THN15WI

Дата модификации: 28.04.2016

Размер: 206.2 Кб

4 стр.

    Товары серии THL 10

    Наименование i Упаковка Каналов U вх Выход U вх ном. U1 I1 Шум КПД U2 I2
    THL 10-1212 (TRACO)
     
    		1 шт — —
    THL 10-2410 (TRACO)
     
    		1 шт — —
    THL 10-2411 (TRACO)
     
    		в линейках 10 шт — —
    THL 10-2412 (TRACO)
     
    		1 шт — —
    THL 10-2413 (TRACO)
     
    		— —
    THL 10-2421 (TRACO)
     
    THL 10-2422 (TRACO)
     
    THL 10-2423 (TRACO)
     
    		в линейках 10 шт
    THL 10-4811 (TRACO)
     
    		— —
    THL 10-4812 (TRACO)
     
    		— —
    THL 10-4823 (TRACO)
     

    THL 10 публикации

    21 июня 2018
    статья

    Особенности программирования изолированных АЦП MAX14001-MAX14002

    MAX14001/MAX14002 – изолированные одноканальные АЦП, предназначенные для создания универсальных дискретных входов или измерительных схем с широким диапазоном входных напряжений. Для настройки параметров АЦП используется SPI–интерфейс.... ...читать