TPB4056A20-DFHR

3PEAK
TPB4056A 1-A Single Cell Battery Linear Charger with High Input Voltage Features Description  Single-Chip Charger for 1-cell Li-ion or Polymer Battery The TPB4056A is a cost-effective, high-integration linear charger for single cell Li-ion or Li-ion polymer batteries. The device support CC/CV charge from either USB port or AC adapter. Low BOM component requirement makes the whole system sma...
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Корпус DFN30308
Режим функционирования
Тип заряжаемого аккумулятора
Интерфейс данных Управление внешними резисторами
Напряжение питания
Максимальный выходной ток
Примечание 1-A Single Cell Battery Linear Charger with High Input Voltage
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 1

показать свернуть
Тип Наименование Корпус Упаковка i Функция Батарея Интерфейс Uвх.макс Uвых U пит Iвых.макс Примечание T раб Карточка
товара
F~ TPB4056A20-DFGR (3PEAK)
 
DFN20208 в ленте 3000 шт
 
 Управление внешними резисторами — — 1-A Single Cell Battery Linear Charger with High Input Voltage

Файлы 1

показать свернуть
TPB4056A 1-A Single Cell Battery Linear Charger with High Input Voltage Features Description  Single-Chip Charger for 1-cell Li-ion or Polymer Battery The TPB4056A is a cost-effective, high-integration linear charger for single cell Li-ion or Li-ion polymer batteries. The device support CC/CV charge from either USB port or AC adapter. Low BOM component requirement makes the whole system small in size. High input voltage range with over-voltage protection supports low-cost unregulated adapters.  Constant-Current/Constant-Voltage Battery Charge  Maximum 1000 mA Programmable Charge Current − Protection − Wide Input From 4.55 V to 6.8 V or to 10.5 V, up to 26.5 V  Charging Current Monitor and Thermal Foldback  Power Presence Indication  Soft start for Inrush Current Limitation  Automatic Battery Recharge  No external MOSFET, Current Sensor or Diode Required  Operation Temperature: −40°C ~ +85°C  Package options: ESOP-8, DFN2×2, DFN3×2, DFN3×3 Applications  Portable Devices, GPS, ePOS, e-cigarette, Walkie-talkie  Wireless Devices, Bluetooth Headset  Personal Electronics, Personal Healthcare The TPB4056A charge current is fully programmable up to 1000 mA with an external resistor. The TPB4056A automatically terminates the charge cycle when the charge current drops below a programmable minimal charging current of the set charge current value after reaches float voltage. The TPB4056A implements two indication pins, PPR and CHG, allowing connection to microcontroller or LED to show device status. With open-drain structure, PPR pin stays low while input voltage is within operation range, and CHG stays low during charging state, else pins are in the high impedance state. The TPB4056A features thermal foldback function to limit the charge current and protect the device from over junction temperature fault. The TPB4056A also integrates current monitor, UVLO, OVP function to prevent device from damage.  Wearable Devices Typical Application Circuit www.3peakic.com.cn 1 / 20 Rev.A.3 PDF
Документация на серию TPB4056A 

Дата модификации: 08.09.2022

Размер: 1.01 Мб

20 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    AP5056 (CHIPOWN)