Вход / Регистрация

BL6513C

Belling
BL6513C Features of BL6513C  Polyphase Active Energy Meter General Description High accuracy, less than 0.1% error over a The BL6513C is the chief IC of the Polyphase dynamic range of 3000:1 electrical  measurement IC. With low power design, static power High stability during calibration, the fluctuation meter and a high accuracy energy of output CF is less than 0.1%. is only 2...
развернуть ▼ свернуть ▲
 

Технические характеристики

показать свернуть
Корпус SOP-24
Измеряемая силовая сеть
Количество измеряемых каналов
Тип выходного сигнала
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Файлы 1

показать свернуть
BL6513C Features of BL6513C  Polyphase Active Energy Meter General Description High accuracy, less than 0.1% error over a The BL6513C is the chief IC of the Polyphase dynamic range of 3000:1 electrical  measurement IC. With low power design, static power High stability during calibration, the fluctuation meter and a high accuracy energy of output CF is less than 0.1%. is only 25mW. Based on the features such as superior  accuracy, high stability and simple peripheral circuit, Low drift, the gain variety is less than 0.1% when input frequency changes from 45Hz to 65Hz the BL6513C is compatible with 3-phase 4-wire or  Single 5V Supply, Static Power 25mW (typical) 3-phase 3-wire configurations.  Power solution only with Resistor & Capacitor BL6513C is based on digital signal processing. can be adopted. BL6513C can measure positive active power and  negative active power; can select the way to calculate Selectable between the arithmetic sum of the three-phase active energies and the absolute value the sum of sum of these energies. the arithmetic sum and the absolute value sum.  the three-phase active powers, between The Low Frequency Output (F1, F2) can drive The high frequency output CF can be used in motor directly; The High Frequency Output (CF) can calibration and data processing. The low frequency be used in calibration and data processing. outputs F1 and F2 can be used to drive a pulse-motor  Anti-Fault, the Logic Output REVP indicates or an electromechanical counter. In this way, the any of the three phase Potential Miswiring or power can be measured and the energy can be Negative Power. recorded.  On-chip Creep Protection.  On-chip Power Supply Monitoring. BL6513C does not exhibit any creep when there is no  On-chip Reference 2.5V ± 8% (30ppm/ ℃ load. An internal no-load threshold ensures that the typical),with External Overdrive Capability. The BL6513C consider emphatically the need of  External clock 3.58MHz stability during calibration, the measure data of mass  SOP24 package products show that the output pulse ripple of CF is  Compatible with 3-phase 4-wire or 3-phase less than 0.1%. 3-wire configurations. Interrelated patents are pending System Diagram Block Fig.1 Functional block diagram http://www.belling.com.cn -1Total 15 Pages V1.0 PDF
Документация на BL6513C 

u

Дата модификации: 18.12.2023

Размер: 599.6 Кб

15 стр.

    Публикации 1

    показать свернуть
    08 октября 2024
    новость

    Трехфазный измеритель электроэнергии Belling

    Shanghai Belling Corp., Ltd. (Belling) был основан Шанхайским муниципальным бюро приборостроения и компанией Shanghai Bell в сентябре 1988 года и изначально носил название Shanghai Belling Microelectronic Mfg. Corp. Ltd. Сегодня Belling занимается... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    71M6542F-IGT/F (MAX)