SD-100A-5

DC/DC преобразователи на шасси
развернуть ▼ свернуть ▲
 
 

Технические характеристики

показать свернуть
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Возможности
Комплекс защит
Номинальное входное напряжение
Напряжение 1 выхода
Напряжение 2 выхода
Напряжение 3 выхода
Ток 1 выхода
Ток 2 выхода
Ток 3 выхода
Уровень пульсаций
КПД
Схема параллельного включения
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Напряжение изоляции выход-земля
Напряжение изоляции между выходами
Сертификаты медицинские
Размер 295×127×41 мм
Рабочая температура
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 2

показать свернуть
Тип Наименование Корпус Упаковка i Монтаж P вых Каналов U вх Выход Возможности Защита U вх ном. U1 U2 U3 I1 I2 I3 Шум КПД Паралл. сх. Uиз. вх-вых Uиз. вх-общ Uиз. вых-общ Uиз. вых-вых Серт. медиц. T раб Примечания Карточка
товара
A- SD-100A-12 (MW)
 
1 шт
A- SD-100A-24 (MW)
 
1 шт

Файлы 2

показать свернуть
SD-100 100W Single Output DC-DC Converter series User’s Manual ■ Features : 2:1 wide input range Protections: Short circuit / Overload / Over voltage 1500VAC I/O isolation Built-in EMI filter, low ripple noise Low cost High reliability 2 years warranty Bauar t gepruft Sicherheit egel ma ge od o s be wac g www. tuv.com ID 2000000000 AS/NZS62368-1 BS EN/EN62368-1 (for D type only) SPECIFICATION MODEL OUTPUT 5V RATED CURRENT 18A CURRENT RANGE RATED POWER 0 ~ 18A 0 ~ 20A 0 ~ 8.5A 0 ~ 4.2A 90W 100W 102W 100.8W 150mVp-p 11 ~ 16VDC 23 ~ 30VDC 4.5 ~ 5.5VDC VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0% ±0.5% ±0.3% ±0.2% LOAD REGULATION ±0.5% ±0.3% ±0.2% SETUP, RISE TIME 2s, 50ms(only D mode) at full load HOLD UP TIME (Typ.) 20ms(only D mode) at full load VOLTAGE RANGE A:9.5 ~ 18VDC EFFICIENCY (Typ.) 78% 74% DC CURRENT (Typ.) INRUSH CURRENT (Typ.) 9.7A/12V 4.8A/24V 2.4A/48V 1.8A/96V 10.4A/12V 4.8A/24V 2.4A/48V 1.8A/96V 10A/12V OVER VOLTAGE WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE B:19 ~ 36VDC 75% C:36 ~ 72VDC 76% 82% 75% D:72 ~ 144VDC or 85 ~ 132VAC 77% 80% 84% 78% 81% 83% 4.8A/24V 2.4A/48V 1.8A/96V D:18A/96VDC <0.75mA/120VAC(SD-100D) 105 ~ 135% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load Protection type : Hiccup mode, recovers automatically after fault condition is removed 31.5 ~ 37.5V 5% load 31.5 ~ 37.5V/10% load -15 ~ +60℃(SD-100A), -10 ~ +60℃(SD-100B/C/D) (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -20 ~ +85℃, 10 ~ 95% RH non-condensing ±0.03%/℃ (0 ~ 50℃) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes IEC/BS EN/EN 62368-1(for D type only), EAC TP TC 004 approved, design refer to AS/NZS 62368.1 I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH Compliance to BS EN/EN55032 (CISPR32) Class B, EAC TP TC 020 EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,6,8, light industry level, criteria A, EAC TP TC 020 MTBF 399.9K hrs min.(SD-100A) 356.7K hrs min.(SD-100B) 355.5K hrs min.(SD-100C) 341.9K Hrs min.(SD-100D) MIL-HDBK-217F (25℃) 199*98*38mm (L*W*H) 0.65Kg; 20pcs/13.8Kg/0.85CUFT DIMENSION PACKING NOTE 4.2A VOLTAGE ADJ. RANGE OVERLOAD OTHERS 24V 8.5A 120mVp-p PROTECTION (Note 4) 12V 20A RIPPLE & NOISE (max.) Note.2 100mVp-p LEAKAGE CURRENT EMC IEC62368-1 (for D type only) SD-100A-5 SD-100B-5 SD-100C-5 SD-100D-5 SD-100A-12 SD-100B-12 SD-100C-12 SD-100D-12 SD-100A-24 SD-100B-24 SD-100C-24 SD-100D-24 DC VOLTAGE LINE REGULATION INPUT TPTC004 1. All parameters NOT specially mentioned are measured at 12,24,48,96VDC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. All the EMC tests are been executed by mounting the unit on a 360mm*360mm metal plate with 1mm of thickness. The final equipment must be re-confirmed that it still meets EMC directives. For guidance on how to perform these EMC tests, please refer to “EMI testing of component power supplies.” (as available on http://www.meanwell.com) 5. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). ※ Product Liability Disclaimer:For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx File Name:SD-100-SPEC 2021-09-15 PDF
Документация на SD-100D-5 

SD-100-20210915.cdr

Дата модификации: 15.09.2021

Размер: 135.3 Кб

3 стр.

SD-100 100W Single Output DC-DC Converter series Features : 2:1 wide input range Protections:Short circuit/Over load/Over voltage 1500VDC I/O isolation Built-in EMI filter, low ripple noise 100% full load burn-in test Fixed switching frequency at 83KHz 24V and 48V input voltage design refer to LVD Low cost High reliability 1 year warranty (for D type only) SPECIFICATION MODEL SD-100B-5 SD-100C-5 SD-100D-5 5V 12V 24V RATED CURRENT 20A 8.5A 4.2A CURRENT RANGE 0 ~ 20A 0 ~ 8.5A 0 ~ 4.2A RATED POWER 100W 102W 100.8W RIPPLE & NOISE (max.) Note.2 100mVp-p OUTPUT INPUT VOLTAGE ADJ. RANGE 1.0% 1.0% 0.5% 0.3% 0.2% LOAD REGULATION 0.5% 0.3% 0.2% SETUP, RISE TIME 2s, 50ms(only D mode) at full load HOLD TIME (Typ.) 24ms(only D mode) at full load VOLTAGE RANGE B:19 ~ 36VDC EFFICIENCY (Typ.) 74% 75% 76% 75% 77% 80% 78% 81% 83% DC CURRENT (Typ.) INRUSH CURRENT (Typ.) 4.8A/24V 2.4A/48V 1.8A/96V 4.8A/24V 2.4A/48V 1.8A/96V 4.8A/24V 2.4A/48V 1.8A/96V C:36 ~ 72VDC D:72 ~ 144VDC or 85 ~ 132VAC D:18A/96VDC LEAKAGE CURRENT <0.75mA/120VAC(SD-100D) OVER LOAD 105 ~ 135% rated output power Protection type : Fold back current limiting, recovers automatically after fault condition is removed WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE 5.75 ~ 6.75V/10% load 16.8 ~ 20V/10% load Protection type : Hiccup mode, recovers automatically after fault condition is removed -10 ~ +60 (Refer to output load derating curve) 31.5 ~ 37.5V/10% load 20 ~ 90% RH non-condensing -20 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes EN60950-1 CB Approved by TUV (for D type only) I/P-O/P:1.5KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMS IMMUNITY Compliance to EN61000-4-2,3,4,6,8; ENV50204 Light industry level, criteria A MTBF 356.7K hrs min.(SD-100B) 355.5K hrs min.(SD-100C) 199*98*38mm (L*W*H) 0.65Kg; 20pcs/13.8Kg/0.8CUFT DIMENSION PACKING NOTE 23 ~ 30VDC 2.0% WORKING TEMP. OTHERS 150mVp-p 11 ~ 16VDC LINE REGULATION OVER VOLTAGE (Note 4) 4.5 ~ 5.5VDC 120mVp-p VOLTAGE TOLERANCE Note.3 PROTECTION EMC SD-100B-12 SD-100C-12 SD-100D-12 SD-100B-24 SD-100C-24 SD-100D-24 DC VOLTAGE 341.9K Hrs min.(SD-100D) MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 24,48,96VDC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:SD-100-SPEC 2006-08-11 PDF
Документация на серию SD-100 

\\Fileserver-s\doc-control\do

Дата модификации: 21.08.2006

Размер: 365.8 Кб

2 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.