NCA9306-DTSHR

Novosense
NCA9306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator Datasheet (EN) 1.2 Product Overview The NCA9306 device is a dual bidirectional I2C and SMBus voltage-level translator with an enable (EN) input, and is operational from 1.2V to 3.3V VREF1 and 1.8V to 5.5V VREF2. The NCA9306 device allows bidirectional voltage translations between 1.2 V and 5 V, without the use of a direction...
развернуть ▼ свернуть ▲
Внешний вид NCA9306-DTSHR

Технические характеристики

показать свернуть
Корпус TSSOP-8
Входной интерфейс
Выходной интерфейс
Примечание
Диапазон рабочих температур
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 1

показать свернуть
Тип Наименование Корпус Упаковка i Вход Выход Скорость Примечание T раб Карточка
товара
F~ TPT29306-VS1R (3PEAK)
 
uSOP-8 MSOP8 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator —

Файлы 1

показать свернуть
NCA9306 Dual Bidirectional I2C Bus and SMBus Voltage-Level Translator Datasheet (EN) 1.2 Product Overview The NCA9306 device is a dual bidirectional I2C and SMBus voltage-level translator with an enable (EN) input, and is operational from 1.2V to 3.3V VREF1 and 1.8V to 5.5V VREF2. The NCA9306 device allows bidirectional voltage translations between 1.2 V and 5 V, without the use of a direction pin. The low ON-state resistance (RON) of the switch allows connections to be made with minimal propagation delay. When EN is high, the translator switch is ON, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively, allowing bidirectional data flow between ports. When EN is low, the translator switch is off, and a high-impedance state exists between ports. In addition to voltage translation, the NCA9306 device can be used to isolate a 400kHz bus from a 100kHz bus by controlling the EN pin to disconnect the slower bus during fast-mode communication. Key Features     2 Bit bidirectional translator for SDA and SCL lines in mixed-mode I2C Applications I2C and SMBus Compatible Less than 1.5-ns Maximum Propagation Delay to Accommodate Standard-mode and Fast-mode I2C Devices and Multiple Masters Allows Voltage-level Translation Between – 1.2V VREF1 and 1.8V, 2.5V, 3.3V, or 5V VREF2 – 1.8V VREF1 and 2.5V, 3.3V, or 5V VREF2 – 2.5V VREF1 and 3.3V or 5V VREF2  Open-drain I2C I/O ports (SCL1, SDA1, SCL2, and SDA2)  5V Tolerant I2C I/O Ports to Support Mixed-mode Signal Operation  High-impedance SCL1, SDA1, SCL2, and SDA2 pins for EN = Low  Lockup-free Operation for Isolation when EN = Low  Flow-through Pinout for Ease of Printed-circuit board Trace Routing  Latch-up Performance Exceeds 100 mA Per JESD 78, Class II  ESD Protection Exceeds JESD 22 – 2000V Human-Body Model (A114-A) – 1000V Charged-Device Model (C101) Applications  I2C, SMBus, PMBus, MDIO, UART, low-speed SDIO, GPIO, and other two-signal interfaces  Servers  Routers (Telecom Switching Equipment)  Personal Computers  Industrial Automation Device Information Part Number NCA9306-DVSR Package VSSOP8 Body Size 2.00mm × 2.30mm NCA9306-DTSHR TSSOP8 3.00mm × 3.00mm Functional Block Diagrams – 3.3V VREF1 and 5V VREF2  Provides Bidirectional Voltage Translation with no Direction Pin  Low 3.5 Ω ON-state Resistance Between Input and Output Ports Provides Less Signal Distortion Figure 1. NCA9306 Block Diagram Copyright © 2019, NOVOSENSE Page 1 PDF
Документация на NCA9306-DTSHR 

AD7792/AD7793 3-Channel, Low Noise, Low Power, 16/24-Bit ∑-Δ ADC with On-Chip In-Amp and Reference Data Sheet (Rev. A) Keywords:

Дата модификации: 05.05.2022

Размер: 4.48 Мб

22 стр.

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    PI7C9X760CZDEX (DIODES)