Серия DC-DC модульных преобразователей K12MT-6

Mornsun

Общие характеристики

 Раздел DC-DC модульные преобразователи
Монтаж
Выходная мощность
Количество каналов
Входное напряжение
Параметры выходов
Возможности подстройка выхода, Remote Sense
Комплекс защит
Номинальное входное напряжение
Напряжение 1 выхода
Ток 1 выхода
КПД
Напряжение изоляции вход-выход
Размер 12.2×12.2×8.7 мм
Рабочая температура

Документация на серию K12MT-6

DC/DC Converter K12MT-6A Series Non-isolated & regulated 6A single output FEATURES POL power converter RoHS     High efficiency up to 94% Wide input voltage range: 4.5VDC-14.4VDC Adjustable output voltage: 0.6VDC-5.5VDC Operating ambient temperature range: -40℃ to +85℃     Output short-circuit protection High-speed transient response Compact SMD package: 12.20 x 12.20 x 8.70mm SENSE, TRIM, PGOOD K12MT-6A series is a 6A non-isolated switching regulator. The output voltage is accurately adjustable from 0.6V to 5.5V, and the product is featured with high efficiency, fast transient response, output short-circuit protection. They are widely used in applications such as communications, computer network industry, power distributed architecture, workstations, servers, LANs/WANs and provide high current with fast transient response for high-speed chips such as FPGA, DSP, and ASIC. Selection Guide Input Voltage (VDC) Certification Part No. -- K12MT-6A-P(N) ① Nominal (Range) 12 （4.5-14.4） Output Max.② Voltage(VDC)③ (Range) Current (A) Max./Min. 15 0.6-5.5 6/0 Efficiency(%) Min./Typ. Capacitive Load(µF) Max. 91/94 1000 Notes: ① “P” indicates that the ON/OFF pin is positive logic control, “N” indicates that the ON/OFF pin is negative logic control; ② Exceeding the maximum input voltage may cause permanent damage; ③ The default output voltage is 0.6VDC, which can be adjusted to 1.2VDC, 1.8VDC, 2.5VDC, 3.3VDC, 5VDC. See Trim instructions for specific output voltage adjustment; ④ Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Input Specifications Item Operating Conditions Min. Typ. Max. Unit Input Current (full load/no-load) Nominal input voltage -- 2660/1 -- mA -- -- 4.5 VDC ① Start-up Voltage Reverse Polarity Input Avoid / Not protected Hot Plug Unavailable Input Filter Capacitance filter K12MT-6A-P (Positive logic) Module on ON/OFF ② Module off K12MT-6A-N (Negative logic) K12MT-6A-P(Positive logic) ON/OFF pin open or pulled high (3VDC ~ Vin) ON/OFF pin open or pulled low to GND (-0.2VDC ~ 0.2VDC) ON/OFF pin pulled low to GND (-0.2VDC ~ 0.2VDC) ON/OFF pin pulled high (3VDC ~ Vin) K12MT-6A-N (Negative logic) Input current when off -- -- 1 mA Min. Typ. Max. Unit -- -- ±1 -- -- ±3 Notes: ① Start-up voltage is 8VDC Max. under the 5VDC output voltage; ② The ON/OFF pin voltage is referenced to GND; ③ Unless otherwise specified, parameters in this table were measured under the 5VDC output voltage. Output Specifications Item Voltage Accuracy Linear Regulation Operating Conditions Input voltage range, 0% -100% load TRIM resistor with 0.1% tolerance TRIM resistor with 1% tolerance % Full load, input voltage Vout≥2.5VDC -- -- ±0.4 % range Vout＜2.5VDC -- -- ±5 mV 2022.09.06-A/0 Page 1 of 6 MORNSUN Guangzhou Science & Technology Co., Ltd. reserves the copyright and right of final interpretation PDF
Документация на серию K12MT-6 

K12MT-6A Keywords:

Дата модификации: 14.09.2023

Размер: 1.93 Мб

6 стр.

    Товары серии K12MT-6

    Наименование i Упаковка
    K12MT-6A-N (MORNSUN)
     
    		в ленте 50 шт
    K12MT-6A-P (MORNSUN)
     
    		в ленте 20 шт