Серия AC-DC сетевых преобразователей DRP-240

MEAN WELL

Общие характеристики

 Раздел AC-DC сетевые преобразователи
Серия
Выходная мощность (ном)
Тип стабилизации
Вход
Конструктивное исполнение
Возможности
Типы защиты КЗ, перегрузка, перенапряжение, перегрев
Количество выходов
Тип управления выходом
Исполнение
Входное напряжение AC
Входное напряжение DC
Коэффициент мощности
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Применение
Размер 125.5×125.2×100 мм
Рабочая температура

Документация на серию DRP-240

240W Single Output Industrial DIN RAIL Power Supply DRP-240 series ■ Features : Universal AC input / Full range Built in active PFC function Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Can be installed on DIN rail TS-35/7.5 or 15 UL 508(industrial control equipment)approved LED indicator for power on 100% full load burn-in test Fixed switching frequency at 100KHz 3 years warranty .. SPECIFICATION MODEL OUTPUT DRP-240-24 DRP-240-48 DC VOLTAGE 24V 48V RATED CURRENT 10A 5A CURRENT RANGE 0 ~ 10A 0 ~ 5A RATED POWER 240W 240W RIPPLE & NOISE (max.) Note.2 80mVp-p 150mVp-p VOLTAGE ADJ. RANGE 48 ~ 53V ±1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 ±1.0% LINE REGULATION ±0.5% LOAD REGULATION ±1.0% SETUP, RISE TIME 800ms, 40ms/230VAC 24ms/230VAC HOLD UP TIME (Typ.) VOLTAGE RANGE INPUT Note.5 85 ~ 264VAC ±0.5% ±1.0% 800ms, 40ms/115VAC at full load 24ms/115VAC at full load 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) EFFICIENCY (Typ.) 0.96/230VAC 84% 0.99/115VAC at full load AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2.8A/115VAC 1.4A/230VAC LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE 85% COLD START 27A/115VAC 45A/230VAC <3.5mA / 240VAC 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 54 ~ 60V 30 ~ 36V Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. -10 ~ +70℃ (Refer to "Derating Curve") WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION 20 ~ 90% RH non-condensing SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION UL508, UL60950-1, TUV EN60950-1 approved OTHERS ±0.03%/℃ (0 ~ 50℃) 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC Compliance to EN55011,EN55032 (CISPR32) Class B, EN61000-3-2,-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A MTBF 289.9Khrs min. MIL-HDBK-217F (25℃) 125.5*125.2*100mm (W*H*D) 1.2Kg; 12pcs/15.5Kg/1.29CUFT DIMENSION PACKING NOTE -20 ~ +85℃, 10 ~ 95% RH 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:DRP-240-SPEC 2017-07-07 PDF
Документация на DRP-240-48 

DRP-240-20170707.cdr

Дата модификации: 04.07.2017

Размер: 80.4 Кб

2 стр.

240W Single Output Industrial DIN RAIL Power Supply DRP-240 series Features : Universal AC input / Full range Built in active PFC function Protections:Short circuit/Over load/Over voltage/Over temperature Cooling by free air convection Can be installed on DIN rail TS-35/7.5 or 15 UL 508(industrial control equipment)approved LED indicator for power on 100% full load burn-in test Fixed switching frequency at 100KHz 3 years warranty R SPECIFICATION MODEL OUTPUT DRP-240-24 DRP-240-48 DC VOLTAGE 24V 48V RATED CURRENT 10A 5A CURRENT RANGE 0 ~ 10A 0 ~ 5A RATED POWER 240W 240W RIPPLE & NOISE (max.) Note.2 80mVp-p 150mVp-p VOLTAGE ADJ. RANGE 48 ~ 53V 1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 1.0% LINE REGULATION 0.5% LOAD REGULATION 1.0% 24ms/230VAC HOLD TIME (Typ.) INPUT 1.0% 800ms, 40ms/230VAC SETUP, RISE TIME VOLTAGE RANGE 0.5% Note.5 85 ~ 264VAC 800ms, 40ms/115VAC at full load 24ms/115VAC at full load 120 ~ 370VDC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) EFFICIENCY (Typ.) 0.96/230VAC 84% 0.99/115VAC at full load AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2.8A/115VAC 1.4A/230VAC LEAKAGE CURRENT OVER LOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE 85% COLD START 27A/115VAC 45A/230VAC <3.5mA / 240VAC 105 ~ 150% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 54 ~ 60V 30 ~ 36V Protection type : Shut down o/p voltage, re-power on to recover 100 5 (TSW1)Detect on heat sink of power transistor Protection type : Shut down o/p voltage, recovers automatically after temperature goes down WORKING TEMP. -10 ~ +70 WORKING HUMIDITY 20 ~ 90% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE -20 ~ +85 (Refer to output load derating curve) , 10 ~ 95% RH 0.03%/ (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL508, UL60950-1, TUV EN60950-1 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC SAFETY & ISOLATION RESISTANCE EMC (Note 4) I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC EMI CONDUCTION & RADIATION Compliance to EN55011,EN55022 (CISPR22) Class B Compliance to EN61000-3-2,-3 HARMONIC CURRENT EMS IMMUNITY MTBF OTHERS DIMENSION PACKING NOTE Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN55024, EN61000-6-2 (EN50082-2) Heavy industry level, criteria A 105.5Khrs min. MIL-HDBK-217F (25 125.5*125.2*100mm (W*H*D) 1.2Kg; 12pcs/15.5Kg/1.2CUFT ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Derating may be needed under low input voltages. Please check the derating curve for more details. File Name:DRP-240-SPEC 2005-06-20 PDF
Документация на серию DRP-240 

DRP-240.cdr

Дата модификации: 08.07.2005

Размер: 339.8 Кб

2 стр.

    Товары серии DRP-240

    Наименование i Упаковка Выход U1 I1 КПД Шум
    DRP-240-24 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 240 Вт; Выход: 24 В; U1: 24...28 В; I1: до 10 А;... в коробках 12 шт
    DRP-240-48 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 240 Вт; Выход: 48 В; U1: 48...53 В; I1: до 5 А; ... в коробках 12 шт

    DRP-240 публикации

    24 апреля 2024
    новость

    MEAN WELL – эксперт по источникам питания. 100 вопросов о ИП MW

    Производя более 10 тысяч стандартных и ряд специализированных моделей источников питания и придерживаясь принципа полной поддержки клиентов, крупнейший мировой производитель ИП, компания MEAN WELL, подготовила список часто задаваемых вопросов о... ...читать

    29 февраля 2016
    новость

    NDR-240/480 – узкие бюджетные источники питания с ККМ на DIN-рейку

    Компания MEAN WELL расширила линейку бюджетных источников питания с креплением на DIN–рейку семейства NDR новыми сериями NDR–240 и NDR–480 с выходной мощностью 240 и 480 Вт соответственно. Новые серии имеют уменьшенную ширину... ...читать