Серия AC-DC сетевых преобразователей TDR-960

MEAN WELL

Общие характеристики

 Раздел AC-DC сетевые преобразователи
Выходная мощность (ном)
Тип стабилизации
Вход
Конструктивное исполнение
Возможности ККМ, сухой контакт DC OK, ограничение тока, параллельное включение
Типы защиты КЗ, перегрузка, перенапряжение, перегрев
Количество выходов
Тип управления выходом
Исполнение
Входное напряжение AC
Входное напряжение DC
Коэффициент мощности
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Напряжение изоляции выход-земля
Применение
Размер 110×125.2×150 мм
Рабочая температура

Документация на серию TDR-960

960W Three Phase Industrial DIN RAIL with PFC Function TDR-960 series ■ Features : User’s Manual Three-Phase 340 ~ 550VAC wide range input (Dual phase operation possible) Width only 110mm Built-in active PFC function compliance to EN61000-3-2 High efficiency 94.5% and low power dissipation Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Built-in constant current limiting circuit Can be installed on DIN rail TS-35/7.5 or 15 UL508(industrial control equipment)approved EN61000-6-2(EN50082-2) industrial immunity level Current sharing up to 3840W(3+1) Built-in DC OK relay contact 100% full load burn-in test 3 years warranty SPECIFICATION UL508 TPTC004 IEC62368-1 MODEL OUTPUT TDR-960-24 TDR-960-48 DC VOLTAGE 24V 48V RATED CURRENT 40A 20A CURRENT RANGE 0 ~ 40A 0 ~ 20A RATED POWER 960W 960W RIPPLE & NOISE (max.) Note.2 180mVp-p 250mVp-p VOLTAGE ADJ. RANGE 48 ~ 55V ±1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 ±1.0% ±0.5% LOAD REGULATION ±1.0% SETUP, RISE TIME 1000ms, 100ms/400VAC VOLTAGE RANGE ±1.0% 12ms / 400VAC HOLD UP TIME (Typ.) INPUT ±0.5% LINE REGULATION 800ms, 100ms/500VAC at full load 14ms / 500VAC at full load Note.4 Three-Phase 340 ~ 550VAC (Dual phase operation possible) 480 ~ 780VDC FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF≧0.88/400VAC EFFICIENCY (Typ.) 94% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2A/400VAC 1.4A/500VAC COLD START 60A LEAKAGE CURRENT <3.5mA / 530VAC 105 ~ 130% rated output power OVERLOAD PF≧0.86/500VAC at full load 94.5% Protection type : Constant current limiting, unit will shut down after 3 sec. ,re-power on to recover 29 ~ 33V Protection type : Shut down o/p voltage, re-power on to recover PROTECTION OVER VOLTAGE 56 ~ 65V Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE DC OK REALY CONTACT RATINGS (max.) 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load FUNCTION Please refer to function manual CURRENT SHARING WORKING TEMP. WORKING HUMIDITY Note.5 -30 ~ +70℃ (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & EMC (Note 6) ±0.03%/℃ (0 ~ 50℃) Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 UL508, AS/NZS62368.1, EAC TP TC 004 approved, IEC62368-1 CB approved by SIQ; Meet BS EN/EN62368-1 I/P-O/P:3KVAC ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH Compliance to BS EN/EN55032 (CISPR32), BS EN/EN61204-3 Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020 EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55024, BS EN/EN61000-6-2 (BS EN/EN50082-2), BS EN/EN61204-3, heavy industry level, criteria A, EAC TP TC 020 59.4K hrs min. MIL-HDBK-217F (25℃) 110*125.2*150mm (W*H*D) 2.47Kg ; 6pcs/15.8Kg/1.47CUFT DIMENSION PACKING NOTE -40 ~ +85℃, 10 ~ 95% RH non-condensing WITHSTAND VOLTAGE MTBF OTHERS 20 ~ 95% RH non-condensing I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Dual phase operation is allowed under certain derating to output load. Please refer to derating curves for details. 5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). ※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx File Name:TDR-960-SPEC 2021- 09-15 PDF
Документация на TDR-960-48 

TDR-960-20210915.cdr

Дата модификации: 15.09.2021

Размер: 113.1 Кб

3 стр.

960W Three Phase Industrial DIN RAIL with PFC Function TDR-960 series ¡½ Features : ¡EThree-Phase 340 ~ 550VAC wide range input (Dual phase operation possible) ¡EWidth only 110mm ¡ Built-in active PFC function compliance to EN61000-3-2 E ¡ High efficiency 94.5% and low power dissipation E ¡ Protections: Short circuit / Overload / Over voltage / Over temperature E ¡ Cooling by free air convection E ¡ Built-in constant current limiting circuit E ¡ Can be installed on DIN rail TS-35/7.5 or 15 E ¡ UL508(industrial control equipment)approved E ¡ EN61000-6-2(EN50082-2) industrial immunity level E ¡ Current sharing up to 3840W(3+1) E ¡ Built-in DC OK relay contact E ¡ 100% full load burn-in test E ¡ 3 years warranty E SPECIFICATION MODEL OUTPUT TDR-960-24 TDR-960-48 DC VOLTAGE 24V 48V RATED CURRENT 40A 20A CURRENT RANGE 0 ~ 40A 0 ~ 20A RATED POWER 960W 960W RIPPLE & NOISE (max.) Note.2 180mVp-p 250mVp-p VOLTAGE ADJ. RANGE 48 ~ 55V ¡Ó1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 ¡Ó1.0% ¡Ó0.5% LOAD REGULATION ¡Ó1.0% SETUP, RISE TIME 1000ms, 100ms/400VAC VOLTAGE RANGE 47 ~ 63Hz PF¡Ù0.88/400VAC EFFICIENCY (Typ.) 94% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2A/400VAC 1.4A/500VAC COLD START 60A LEAKAGE CURRENT <3.5mA / 530VAC 105 ~ 130% rated output power PF¡Ù0.86/500VAC at full load 94.5% Protection type : Constant current limiting, unit will shut down after 3 sec. ,re-power on to recover OVER TEMPERATURE 29 ~ 33V Protection type : Shut down o/p voltage, re-power on to recover 56 ~ 65V 90¢J ¡Ó5¢J (TSW) detect on heatsink of power switch 85¢J ¡Ó5¢J (TSW) detect on heatsink of power switch Protection type : Shut down o/p voltage, recovers automatically after temperature goes down DC OK REALY CONTACT RATINGS (max.) 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load Please refer to function manual CURRENT SHARING WORKING TEMP. WORKING HUMIDITY Note.5 -30 ~ +70¢J (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING NOTE 14ms / 500VAC at full load FREQUENCY RANGE POWER FACTOR (Typ.) PROTECTION OVER VOLTAGE OTHERS 800ms, 100ms/500VAC at full load Note.4 Three-Phase 340 ~ 550VAC (Dual phase operation possible) 480 ~ 780VDC OVERLOAD FUNCTION ¡Ó1.0% 12ms / 400VAC HOLD UP TIME (Typ.) INPUT ¡Ó0.5% LINE REGULATION 20 ~ 95% RH non-condensing -40 ~ +85¢J, 10 ~ 95% RH ¡Ó0.03%/¢J (0 ~ 50¢J) Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 UL508 approved, IEC60950-1 CB approved by SIQ I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25¢J/ 70% RH Compliance to EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A 59.4K hrs min. MIL-HDBK-217F (25¢J) 110*125.2*150mm (W*H*D) 2.47Kg ; 6pcs/15.8Kg/1.47CUFT 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25¢J of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Dual phase operation is allowed under certain derating to output load. Please refer to derating curves for details. 5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:TDR-960-SPEC 2012-10-12 PDF
Документация на серию TDR-960 

TDR-960.cdr Keywords:

Дата модификации: 17.10.2012

Размер: 160.6 Кб

3 стр.

    Товары серии TDR-960

    Наименование i Упаковка Выход U1 I1 КПД Шум
    TDR-960-24 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 960 Вт; Выход: 24 В; U1: 24...28 В; I1: до 40 А;... в коробках 6 шт
    TDR-960-48 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 960 Вт; Выход: 48 В; U1: 48...55 В; I1: до 20 А;... в коробках 6 шт

    TDR-960 публикации

    30 сентября 2025
    новость

    Новые трехфазные ИП MEAN WELL XTR: ультратонкие, эффективные, надежные

    На склад КОМПЭЛ поступила новая серия источников питания MEAN WELL XTR, предназначенная для трехфазных сетей. Ознакомиться с параметрами устройств мощностью 240, 480 и 960 Вт можно в нашем каталоге. Ключевые преимущества новой серии XTR (таблица... ...читать

    16 сентября 2022
    новость

    Актуальные вопросы о продукции и планах MEAN WELL в России (материалы вебинара)

    Программа показатьсвернуть Приглашаем на онлайн–семинар, который проведет КОМПЭЛ совместно с представителями бренда MEAN WELL. На нем будут даны ответы на интересующие вас вопросы о продукции, особенностях работы в текущих условиях и... ...читать

    06 мая 2013
    новость

    SDR/TDR-960 – мощные источники питания с пассивным охлаждением на DIN-рейку

    Компания MEAN WELL расширила семейство однофазных источников питания SDR для установки на DIN–рейку, выпустив новые серии SDR–960 и TDR–960. Источники двух новых серий обладают схожими характеристиками, но различаются диапазоном... ...читать