TDR-960-48

MEAN WELL
AC/DC преобразователи на DIN рейку
развернуть ▼ свернуть ▲
Фотография серии TDR-960

Технические характеристики

показать свернуть
Выходная мощность (ном)
Выход
Напряжение 1 канала
Выходной ток 1 канала
Тип стабилизации
Вход
Конструктивное исполнение
Возможности ККМ, сухой контакт DC OK, ограничение тока, параллельное включение
Типы защиты КЗ, перегрузка, перенапряжение, перегрев
Количество выходов
Тип управления выходом
Исполнение
Входное напряжение AC
Входное напряжение DC
Коэффициент мощности
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Напряжение изоляции выход-земля
Применение
КПД
Шум
Размер 110×125.2×150 мм
Рабочая температура
Примечание AC-DC Power Factor Correction Module, 1 Output, 960W, Hybrid
Нашли ошибку? Выделите её курсором и нажмите CTRL + ENTER

Аналоги 1

показать свернуть
Тип Наименование Корпус Упаковка i P вых Выход U1 I1 Стабилизация Вход Конструктив Возможности Защита Выходов Управление IP U вх AC U вх DC Коэф. мощн. U изол вх-вых U изол вх-земля U изол вых-земля Применение КПД Шум T раб Примечание Карточка
товара
A+ SDR-960-48 (MW)
 
— в коробках 6 шт AC-DC сетевой преобразователь - P вых: 960 Вт; Выход: 48 В; U1: 48...55 В; I1: до 26 А;... ККМ, сухой контакт DC OK, ограничение тока, параллельное включение, пиковая перегрузка КЗ, перегрузка, перенапряжение, перегрев

Файлы 2

показать свернуть
960W Three Phase Industrial DIN RAIL with PFC Function TDR-960 series ■ Features : User’s Manual Three-Phase 340 ~ 550VAC wide range input (Dual phase operation possible) Width only 110mm Built-in active PFC function compliance to EN61000-3-2 High efficiency 94.5% and low power dissipation Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Built-in constant current limiting circuit Can be installed on DIN rail TS-35/7.5 or 15 UL508(industrial control equipment)approved EN61000-6-2(EN50082-2) industrial immunity level Current sharing up to 3840W(3+1) Built-in DC OK relay contact 100% full load burn-in test 3 years warranty SPECIFICATION UL508 TPTC004 IEC62368-1 MODEL OUTPUT TDR-960-24 TDR-960-48 DC VOLTAGE 24V 48V RATED CURRENT 40A 20A CURRENT RANGE 0 ~ 40A 0 ~ 20A RATED POWER 960W 960W RIPPLE & NOISE (max.) Note.2 180mVp-p 250mVp-p VOLTAGE ADJ. RANGE 48 ~ 55V ±1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 ±1.0% ±0.5% LOAD REGULATION ±1.0% SETUP, RISE TIME 1000ms, 100ms/400VAC VOLTAGE RANGE ±1.0% 12ms / 400VAC HOLD UP TIME (Typ.) INPUT ±0.5% LINE REGULATION 800ms, 100ms/500VAC at full load 14ms / 500VAC at full load Note.4 Three-Phase 340 ~ 550VAC (Dual phase operation possible) 480 ~ 780VDC FREQUENCY RANGE POWER FACTOR (Typ.) 47 ~ 63Hz PF≧0.88/400VAC EFFICIENCY (Typ.) 94% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2A/400VAC 1.4A/500VAC COLD START 60A LEAKAGE CURRENT <3.5mA / 530VAC 105 ~ 130% rated output power OVERLOAD PF≧0.86/500VAC at full load 94.5% Protection type : Constant current limiting, unit will shut down after 3 sec. ,re-power on to recover 29 ~ 33V Protection type : Shut down o/p voltage, re-power on to recover PROTECTION OVER VOLTAGE 56 ~ 65V Shut down o/p voltage, recovers automatically after temperature goes down OVER TEMPERATURE DC OK REALY CONTACT RATINGS (max.) 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load FUNCTION Please refer to function manual CURRENT SHARING WORKING TEMP. WORKING HUMIDITY Note.5 -30 ~ +70℃ (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & EMC (Note 6) ±0.03%/℃ (0 ~ 50℃) Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 UL508, AS/NZS62368.1, EAC TP TC 004 approved, IEC62368-1 CB approved by SIQ; Meet BS EN/EN62368-1 I/P-O/P:3KVAC ISOLATION RESISTANCE EMC EMISSION I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH Compliance to BS EN/EN55032 (CISPR32), BS EN/EN61204-3 Class B, BS EN/EN61000-3-2,-3, EAC TP TC 020 EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN55024, BS EN/EN61000-6-2 (BS EN/EN50082-2), BS EN/EN61204-3, heavy industry level, criteria A, EAC TP TC 020 59.4K hrs min. MIL-HDBK-217F (25℃) 110*125.2*150mm (W*H*D) 2.47Kg ; 6pcs/15.8Kg/1.47CUFT DIMENSION PACKING NOTE -40 ~ +85℃, 10 ~ 95% RH non-condensing WITHSTAND VOLTAGE MTBF OTHERS 20 ~ 95% RH non-condensing I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Dual phase operation is allowed under certain derating to output load. Please refer to derating curves for details. 5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 7. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). ※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx File Name:TDR-960-SPEC 2021- 09-15 PDF
Документация на TDR-960-48 

TDR-960-20210915.cdr

Дата модификации: 15.09.2021

Размер: 113.1 Кб

3 стр.

960W Three Phase Industrial DIN RAIL with PFC Function TDR-960 series ¡½ Features : ¡EThree-Phase 340 ~ 550VAC wide range input (Dual phase operation possible) ¡EWidth only 110mm ¡ Built-in active PFC function compliance to EN61000-3-2 E ¡ High efficiency 94.5% and low power dissipation E ¡ Protections: Short circuit / Overload / Over voltage / Over temperature E ¡ Cooling by free air convection E ¡ Built-in constant current limiting circuit E ¡ Can be installed on DIN rail TS-35/7.5 or 15 E ¡ UL508(industrial control equipment)approved E ¡ EN61000-6-2(EN50082-2) industrial immunity level E ¡ Current sharing up to 3840W(3+1) E ¡ Built-in DC OK relay contact E ¡ 100% full load burn-in test E ¡ 3 years warranty E SPECIFICATION MODEL OUTPUT TDR-960-24 TDR-960-48 DC VOLTAGE 24V 48V RATED CURRENT 40A 20A CURRENT RANGE 0 ~ 40A 0 ~ 20A RATED POWER 960W 960W RIPPLE & NOISE (max.) Note.2 180mVp-p 250mVp-p VOLTAGE ADJ. RANGE 48 ~ 55V ¡Ó1.0% 24 ~ 28V VOLTAGE TOLERANCE Note.3 ¡Ó1.0% ¡Ó0.5% LOAD REGULATION ¡Ó1.0% SETUP, RISE TIME 1000ms, 100ms/400VAC VOLTAGE RANGE 47 ~ 63Hz PF¡Ù0.88/400VAC EFFICIENCY (Typ.) 94% AC CURRENT (Typ.) INRUSH CURRENT (Typ.) 2A/400VAC 1.4A/500VAC COLD START 60A LEAKAGE CURRENT <3.5mA / 530VAC 105 ~ 130% rated output power PF¡Ù0.86/500VAC at full load 94.5% Protection type : Constant current limiting, unit will shut down after 3 sec. ,re-power on to recover OVER TEMPERATURE 29 ~ 33V Protection type : Shut down o/p voltage, re-power on to recover 56 ~ 65V 90¢J ¡Ó5¢J (TSW) detect on heatsink of power switch 85¢J ¡Ó5¢J (TSW) detect on heatsink of power switch Protection type : Shut down o/p voltage, recovers automatically after temperature goes down DC OK REALY CONTACT RATINGS (max.) 60Vdc/0.3A, 30Vdc/1A, 30Vac/0.5A resistive load Please refer to function manual CURRENT SHARING WORKING TEMP. WORKING HUMIDITY Note.5 -30 ~ +70¢J (Refer to "Derating Curve") ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION EMC IMMUNITY MTBF DIMENSION PACKING NOTE 14ms / 500VAC at full load FREQUENCY RANGE POWER FACTOR (Typ.) PROTECTION OVER VOLTAGE OTHERS 800ms, 100ms/500VAC at full load Note.4 Three-Phase 340 ~ 550VAC (Dual phase operation possible) 480 ~ 780VDC OVERLOAD FUNCTION ¡Ó1.0% 12ms / 400VAC HOLD UP TIME (Typ.) INPUT ¡Ó0.5% LINE REGULATION 20 ~ 95% RH non-condensing -40 ~ +85¢J, 10 ~ 95% RH ¡Ó0.03%/¢J (0 ~ 50¢J) Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 UL508 approved, IEC60950-1 CB approved by SIQ I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25¢J/ 70% RH Compliance to EN55022 (CISPR22), EN61204-3 Class B, EN61000-3-2,-3 Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A 59.4K hrs min. MIL-HDBK-217F (25¢J) 110*125.2*150mm (W*H*D) 2.47Kg ; 6pcs/15.8Kg/1.47CUFT 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25¢J of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. Dual phase operation is allowed under certain derating to output load. Please refer to derating curves for details. 5. Installation clearances : 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. 6. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:TDR-960-SPEC 2012-10-12 PDF
Документация на серию TDR-960 

TDR-960.cdr Keywords:

Дата модификации: 17.10.2012

Размер: 160.6 Кб

3 стр.

    Публикации 2

    показать свернуть
    19 июля 2022
    статья

    Организация низковольтных систем бесперебойного питания для промышленных приложений на базе компонентов MEAN WELL

    Игорь Елисеев (г. Химки) Для реализации низковольтной промышленной системы бесперебойного электропитания не подходят стандартные ИБП. MEAN WELL предлагает для этого системы на DIN–рейку на базе UPS–контроллеров и аккумуляторных... ...читать

    08 апреля 2014
    статья

    DIN-рейка плюс электросеть: источники электропитания для промышленной автоматики и систем безопасности

    Как выбрать необходимое в обширной номенклатуре AC/DC–модулей, предлагаемых компанией КОМПЭЛ для организации электропитания промавтоматики и систем безопасности? Рассмотрим продукцию трех производителей – MEAN WELL, TDK–Lambda и... ...читать

    Внимание! Точность указанного на сайте описания товара не может быть гарантирована. Для получения более полной и точной информации о товаре смотрите техническое описание (Datasheet) на сайте производителя.

    AD-155A (MW)