Серия AC-DC сетевых преобразователей WDR-120

MEAN WELL

Общие характеристики

 Раздел AC-DC сетевые преобразователи
Выходная мощность (ном)
Тип стабилизации
Вход
Конструктивное исполнение
Возможности сухой контакт DC OK, ограничение тока
Типы защиты КЗ, перегрузка, перенапряжение, перегрев
Количество выходов
Тип управления выходом
Исполнение
Входное напряжение AC
Входное напряжение DC
Коэффициент мощности
Напряжение изоляции вход-выход
Напряжение изоляции вход-земля
Напряжение изоляции выход-земля
Применение
Размер 40×125×113 мм
Рабочая температура

Документация на серию WDR-120

120W Single Output Industrial DIN RAIL Power Supply WDR-120 series User’s Manual ■ Features : Single and two phase wide input range 180 ~ 550VAC Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Built-in constant current limiting circuit Can be installed on DIN rail TS-35/7.5 or 15 UL508(industrial control equipment)approved BS EN/EN61000-6-2(BS EN/EN50082-2) industrial immunity level 100% full load burn-in test Built-in DC OK relay contact 3 years warranty SPECIFICATION MODEL OUTPUT AS/NZS62368-1 TPTC004 WDR-120-24 WDR-120-48 DC VOLTAGE 12V 24V 48V RATED CURRENT 10A 5A 2.5A CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~2.5A RATED POWER 120W 120W 120W RIPPLE & NOISE (max.) Note.2 120mVp-p 120mVp-p 150mVp-p VOLTAGE ADJ. RANGE 12 ~ 15V VOLTAGE TOLERANCE Note.3 ±1.5% 24 ~ 29V ±1.0% 48 ~ 58V ±1.0% LINE REGULATION ±0.5% ±0.5% ±0.5% LOAD REGULATION ±0.5% ±0.5% ±0.5% SETUP, RISE, HOLD UP TIME 2000ms, 70ms, 50ms/400VAC INPUT VOLTAGE RANGE 180 ~ 550VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 89.5% / 400V AC CURRENT INRUSH CURRENT (max.) 0.7A/400VAC 1.2A/230VAC COLD START 50A LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE OVER TEMPERATURE FUNCTION DC OK SIGNAL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) EMC EMISSION OTHERS IEC62368-1 2000ms, 70ms, 10ms/230VAC at full load 254 ~ 780VDC 91% / 400V 92% / 400V <3.5mA / 530VAC 105 ~ 130% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 16 ~ 18V 31 ~ 37V 60 ~ 67V Protection type : Shut down o/p voltage, re-power on to recover Shut down o/p voltage, recovers automatically after temperature goes down Relay contact rating(max.) : 30V / 1A resistive -25 ~ +70℃ (Refer to "Derating Curve") 20 ~ 90% RH non-condensing -40 ~ +85℃, 10 ~ 95% RH ±0.03%/℃ (0 ~ 50℃) Component: 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting clip: Compliance to IEC60068-2-6 UL508, EAC TP TC 004 approved, IEC62368-1 CB approved by SIQ;Design refer to BS EN/EN62368-1, AS/NZS 62368.1 (meet BS EN/EN60204-1) I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH Compliance to BS EN/EN55032 (CISPR32), BS EN/EN61204-3 Class B, EAC TP TC 020 EMC IMMUNITY Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61204-3, BS EN/EN61000-6-2 (BS EN/EN50082-2), heavy industry level, criteria A, EAC TP TC 020 MTBF 268K hrs min. DIMENSION 40*125.2*113.5mm (W*H*D) 0.65Kg; 20pcs/14Kg/1.16CUFT PACKING NOTE UL508 WDR-120-12 MIL-HDBK-217F (25℃) 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead to increase of the set up time. 6. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft). ※ Product Liability Disclaimer：For detailed information, please refer to https://www.meanwell.com/serviceDisclaimer.aspx File Name:WDR-120-SPEC 2021-09-15 PDF
Документация на WDR-120-48 

WDR-120-20210915.cdr

Дата модификации: 15.09.2021

Размер: 102.4 Кб

3 стр.

120W Single Output Industrial DIN RAIL Power Supply WDR-120 series Features : Single and two phase wide input range 180 ~ 550VAC Protections: Short circuit / Overload / Over voltage / Over temperature Cooling by free air convection Built-in constant current limiting circuit Can be installed on DIN rail TS-35/7.5 or 15 UL508(industrial control equipment)approved EN61000-6-2(EN50082-2) industrial immunity level 100% full load burn-in test Built-in DC OK relay contact 3 years warranty SPECIFICATION MODEL OUTPUT WDR-120-12 WDR-120-24 WDR-120-48 DC VOLTAGE 12V 24V 48V RATED CURRENT 10A 5A 2.5A CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~2.5A RATED POWER 120W 120W 120W RIPPLE & NOISE (max.) Note.2 120mVp-p 120mVp-p 150mVp-p VOLTAGE ADJ. RANGE 24 ~ 29V 1.0% 48 ~ 58V 1.0% 12 ~ 15V VOLTAGE TOLERANCE Note.3 1.5% LINE REGULATION 0.5% 0.5% 0.5% LOAD REGULATION 0.5% 0.5% 0.5% SETUP, RISE, HOLD UP TIME 2000ms, 70ms, 50ms/400VAC INPUT VOLTAGE RANGE 180 ~ 550VAC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 89.5% / 400V AC CURRENT INRUSH CURRENT (max.) 0.55A/400VAC 1.2A/230VAC COLD START 50A LEAKAGE CURRENT OVERLOAD PROTECTION OVER VOLTAGE FUNCTION DC OK SIGNAL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE ISOLATION RESISTANCE EMC (Note 4) 92% / 400V <3.5mA / 530VAC 5 (12V),110 5 (24V) (TSW1) detect on heatsink of power transistor ; 100 5 (48V) (TSW1) detect on heatsink of power diode Protection type : Shut down o/p voltage, recovers automatically after temperature goes down Relay contact rating(max.) : 30V / 1A resistive -25 ~ +70 (Refer to output load derating curve) 20 ~ 90% RH non-condensing -40 ~ +85 , 10 ~ 95% RH 0.03%/ (0 ~ 50 Component: 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting clip: Compliance to IEC60068-2-6 UL508 approved, IEC60950-1 CB approved by SIQ, design refer to GL I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC Compliance to EN61000-4-2,3,4,5,6,8,11, ENV50204, EN61204-3, EN61000-6-2 (EN50082-2), heavy industry level, criteria A MTBF 268Khrs min. DIMENSION 40*125.2*113.5mm (W*H*D) 0.65Kg; 20pcs/14Kg/1.16CUFT PACKING NOTE 91% / 400V I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25 / 70% RH EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B EMS IMMUNITY OTHERS 254 ~ 780VDC 105 ~ 130% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed 16 ~ 18V 31 ~ 37V 60 ~ 67V Protection type : Shut down o/p voltage, re-power on to recover 105 OVER TEMPERATURE 2000ms, 70ms, 10ms/230VAC at full load MIL-HDBK-217F (25 ) 1. All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead to increase of the set up time. File Name:WDR-120-SPEC 2010-12-07 PDF
Документация на серию WDR-120 

WDR-120.cdr

Дата модификации: 08.12.2010

Размер: 333.7 Кб

3 стр.

    Товары серии WDR-120

    Наименование i Упаковка Выход U1 I1 КПД Шум
    WDR-120-12 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 120 Вт; Выход: 12 В; U1: 12...15 В; I1: до 10 А;... в коробках 20 шт
    WDR-120-24 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 120 Вт; Выход: 24 В; U1: 24...29 В; I1: до 5 А; ... в коробках 20 шт
    WDR-120-48 (MW)
     
    		AC-DC сетевой преобразователь - P вых: 120 Вт; Выход: 48 В; U1: 48...58 В; I1: до 2.5 А... в коробках 20 шт

    WDR-120 публикации

    12 мая 2022
    новость

    Источники питания MEAN WELL для промавтоматики и серверного оборудования в новых условиях (материалы вебинара)

    Программа показатьсвернуть Приглашаем всех желающих на вебинар, посвященный линейке продукции MEAN WELL для промышленной автоматизации и оборудования, систем охраны, серверного, телекоммуникационного оборудования и базовых станций 4G/5G. На... ...читать

    02 марта 2021
    новость

    WDR-60 от Mean Well – источник питания на DIN-рейку со сверхшироким входом

    Компания Mean Well расширяет семейство одно– и двухфазных источников питания со сверхшироким диапазоном входного напряжения, предназначенных для монтажа на DIN–рейку, дополнив его серией WDR–60. В настоящий момент, помимо серий... ...читать